Husqvarna TX 300i 2022

Questions and Answers

J
James BoltonAug 16, 2025
Why won't my Husqvarna TX 300i 2022 Motorcycle engine crank?
- J
  Jeremy HicksAug 16, 2025
  If the engine of your Husqvarna Motorcycle won't crank, possible causes include: * An operating error. Perform the start procedure. * A discharged 12-V battery. Charge the 12-V battery and check the charging voltage, closed current, and stator winding of the alternator. * A blown main fuse. Replace the main fuse. * A faulty starter relay. Check the starter relay. * A faulty starter motor. Check the starter motor.
C
carol48Aug 22, 2025
How to prevent my Husqvarna TX 300i 2022 engine from overheating?
- M
  Michael GreenAug 22, 2025
  To prevent your Husqvarna Motorcycle engine from overheating: * Check for coolant leakage and ensure the coolant level is correct. * Avoid prolonged idling; switch off the engine when stationary to ensure sufficient air stream. * Clean the radiator fins to remove dirt. * Address foam formation by draining and refilling the cooling system. * Inspect the cylinder head and cylinder head gasket for damage. * Replace any bent radiator hoses. * Check the thermostat; the guideline opening temperature is 70 °C (158 °F).
J
jenniferbryantAug 26, 2025
Why does my Husqvarna TX 300i 2022 engine have low power?
- N
  Nathan AdamsAug 26, 2025
  If your Husqvarna Motorcycle engine has too little power, the following could be the reasons: * The air filter is very dirty. Clean the air filter and air filter box. * The fuel filter is very dirty. Change the fuel filter. * The fuel screen is very dirty. Change the fuel screen.
K
Kimberly WarrenAug 28, 2025
What causes my Husqvarna TX 300i 2022 Motorcycle engine to die while riding?
- K
  Kim HouseAug 28, 2025
  Your Husqvarna Motorcycle engine may die during a trip due to: * Lack of fuel. Refuel. * The engine taking in false air. Check that the intake flange is firmly seated. * A loose or oxidized connector or ignition coil. Clean the connector and treat it with contact spray. * Incorrectly stored ambient pressure. Program ambient air pressure.
P
Patricia LoweAug 31, 2025
Why won't my Husqvarna TX 300i 2022 Motorcycle engine idle?
- P
  Paul JonesAug 31, 2025
  If your Husqvarna Motorcycle engine has no idle speed, possible causes include: * A defective spark plug. Change the spark plug. * A defective ignition system. Check the ignition coil and spark plug connector. * Incorrect idle speed setting. Adjust the idle speed.
A
angela00Sep 3, 2025
Why my Husqvarna TX 300i 2022 engine won't accelerate?
- G
  georgealexisSep 3, 2025
  If your Husqvarna Motorcycle engine does not speed up, consider these potential causes: * Malfunction in the electronic fuel injection. Read out the fault memory using the Husqvarna Motorcycles diagnostics tool. * Defective ignition system. Check the ignition coil and spark plug connector. * Incorrectly stored ambient pressure. Program ambient air pressure.
R
Robert MoralesSep 6, 2025
Why is my Husqvarna Motorcycle emitting white smoke?
- M
  Marco OdomSep 6, 2025
  White smoke emitting from your Husqvarna Motorcycle exhaust gas, indicates a damaged cylinder head or cylinder head gasket. Check the cylinder head and cylinder head gasket.
A
Alexis CannonSep 9, 2025
Why is gear oil coming out of the vent hose on my Husqvarna Motorcycle?
- E
  edwardmathewsSep 9, 2025
  If gear oil is exiting at the vent hose of your Husqvarna Motorcycle, it means that too much gear oil was added. Check the gear oil level.
B
brittanysmithSep 12, 2025
How water gets in the gear oil of my Husqvarna TX 300i 2022 Motorcycle?
- T
  tammieholdenSep 12, 2025
  If there is water in the gear oil of your Husqvarna Motorcycle, it could be due to a damaged radial shaft seal ring or water pump. Check the radial shaft seal ring and the water pump.
A
Amy HoffmanNov 18, 2025
What to do if my Husqvarna TX 300i 2022 engine turns over but won't start?
- J
  James PhillipsNov 18, 2025
  If your Husqvarna Motorcycle engine turns over but doesn't start, consider these potential causes: * An operating error. Perform the start procedure. * The quick release coupling is not joined. Join the quick release coupling. * Incorrect idle speed. Adjust the idle speed. * Interrupted fuel supply. Check the fuel tank breather. * Sooty or wet spark plug. Clean and dry the spark plug and spark plug connector, or replace if necessary. * Spark plug gap too wide. Adjust the plug gap to the recommended 0.6 mm (0.024 in). * Defective ignition system. Check the ignition coil and spark plug connector. * Frayed short-circuit cable or faulty stop button. Check the stop button. * Loose or oxidized connector or ignition coil. Clean the connector and treat it with contact spray. * ...

Summary

Means of Representation

Symbols Used

Explains the meaning of specific symbols used in the manual.

Formats Used

Explains the typographical formats used in the document.

Safety Advice

Use Definition - Intended Use

Defines the intended use of the vehicle and its compliance with motorsports regulations.

Degrees of Risk and Symbols

Explains the different risk levels (Danger, Warning, Caution, Note) and their symbols.

Safe Operation

Provides essential safety guidelines for operating the motorcycle.

Important Notes

Manufacturer Warranty, Implied Warranty

Details warranty conditions and voiding clauses for service work.

Service

Explains how service and tuning affect vehicle operation and lifespan.

View of Vehicle

View of Vehicle, Front Left (Example)

Identifies key components on the front left view of the motorcycle.

View of Vehicle, Rear Right (Example)

Identifies key components on the rear right view of the motorcycle.

Serial Numbers

Vehicle Identification Number

Shows where to find the vehicle identification number.

Engine Number

Shows where the engine number is embossed.

Controls

Clutch Lever

Describes the function and operation of the clutch lever.

Throttle Grip

Identifies the throttle grip and its location.

Overview of Indicator Lights

Explains the meaning of the malfunction and warning lamps.

Preparing for Use

Advice on Preparing for First Use

Provides crucial advice and safety warnings before operating the vehicle for the first time.

Preparing the Vehicle for Difficult Operating Conditions

Advises on preparing the vehicle for challenging riding environments.

Riding Instructions

Checks and Maintenance Measures When Preparing for Use

Lists essential pre-ride checks and maintenance tasks for safety.

Applying the Brakes

Advises on proper brake application techniques and safety.

Refueling

Details the procedure and safety precautions for refueling.

Service Schedule

Required Work

Lists mandatory maintenance tasks at different operating hour intervals.

Tuning the Chassis

Checking the Basic Chassis Setting with the Riders Weight

Explains how rider weight affects chassis settings and adjustment.

Adjusting the Low-Speed Compression Damping of the Shock Absorber

Details how to adjust the low-speed compression damping.

Adjusting the Fork Air Pressure

Details how to adjust the air pressure in the fork.

Service Work on the Chassis

Removing the Fork Legs

Explains how to remove the front fork legs.

Installing the Fork Legs

Details how to install the front fork legs correctly.

Removing the Shock Absorber

Guides on removing the rear shock absorber.

Installing the Shock Absorber

Guides on installing the rear shock absorber.

Brake System

Checking the Front Brake Fluid Level

Details how to check the front brake fluid level.

Changing the Brake Linings of the Front Brake

Details how to change the front brake linings.

Checking the Rear Brake Fluid Level

Details how to check the rear brake fluid level.

Changing the Rear Brake Linings

Details how to change the rear brake linings.

Wheels, Tires

Removing the Front Wheel

Guides on removing the front wheel.

Installing the Front Wheel

Guides on installing the front wheel.

Checking Tire Pressure

Details how to check and correct tire pressure.

Electrical System

Removing the 12-V Battery

Details how to safely remove the 12-V battery.

Installing the 12-V Battery

Details how to safely install the 12-V battery.

Charging the 12-V Battery

Provides instructions and safety for charging the 12-V battery.

Cooling System

Checking the Antifreeze and Coolant Level

Guides on checking antifreeze and coolant levels with safety warnings.

Checking the Coolant Level

Details how to check the coolant level in the radiator with safety warnings.

Changing the Coolant

Details the process for changing the coolant, with safety warnings.

Tuning the Engine

Adjusting the Play in the Throttle Cable

Details how to adjust the throttle cable play.

Adjusting the Idle Speed

Guides on adjusting the engine's idle speed.

Service Work on the Engine

Changing the Fuel Screen

Details how to change the fuel screen with safety warnings.

Checking 2-Stroke Oil Level

Explains how to check the 2-stroke oil level.

Checking the Gear Oil Level

Explains how to check the gear oil level.

Changing the Gear Oil

Details how to change the gear oil, including safety warnings.

Cleaning, Care

Cleaning the Motorcycle

Provides instructions for cleaning the motorcycle, including warnings about pressure washers.

Storage

Outlines steps for preparing the motorcycle for long-term storage.

Preparing for Use After Storage

Explains how to prepare the motorcycle for use after it has been stored.

Technical Data

Engine

Lists engine specifications.

Chassis

Lists various chassis specifications.

Fork

Lists fork specifications, including adjustments.

Shock Absorber

Lists shock absorber specifications, including adjustments.

Substances

Brake Fluid DOT 4; DOT 5.1

Specifies standards and recommended suppliers for brake fluid.

Coolant

Details coolant specifications, properties, and recommended suppliers.

Engine Oil (15 W;50)

Lists engine oil standards, classification, and recommended suppliers.

Engine Oil, 2-Stroke

Specifies standards and guidelines for 2-stroke engine oil.

Auxiliary Substances

Air Filter Cleaner

Lists recommended supplier and product for air filter cleaner.

Chain Cleaner

Lists recommended supplier and product for chain cleaner.

Motorcycle Cleaner

Lists recommended supplier and product for motorcycle cleaner.

Universal Oil Spray

Lists recommended supplier and product for universal oil spray.

Standards

JASO T903 MA2

Explains the JASO T903 MA2 standard for motorcycle engine oils.

SAE

Explains SAE viscosity classes for oils.

JASO FD

Describes the JASO FD classification for 2-stroke engine oil.

List of Symbols

Red Symbols

Explains that red symbols indicate errors requiring immediate intervention.

Yellow and Orange Symbols

Explains that yellow/orange symbols indicate errors requiring prompt intervention.

Husqvarna TX 300i 2022 Specifications

General

Displacement	293.2 cc
Bore x Stroke	72 mm x 72 mm
Transmission	6-speed
Seat Height	950 mm
Fuel Tank Capacity	8.5 l
Rear Suspension	WP XACT shock absorber with linkage
Front Brake	Brembo, Disc brake
Rear Brake	Brembo, Disc brake
Starter	Electric starter
Engine Type	2-stroke, single cylinder
Fuel System	Electronic Fuel Injection
Cooling System	Liquid cooling
Front Suspension	WP XPLOR 48