Husqvarna TE 300i - User Manual

Questions and Answers

K
Kenneth PowellAug 18, 2025
What to do if Husqvarna TE 300i Motorcycle engine cannot be cranked using the electric starter?
- W
  william30Aug 19, 2025
  If the Husqvarna Motorcycle engine cannot be cranked, possible causes include operating error (carry out the start procedure), a discharged battery (recharge the battery, check the charging voltage, open-circuit current, and stator winding of the alternator), a blown main fuse (change the main fuse), a faulty starter relay (check the starter relay), or a faulty starter motor (check the starter motor).
R
randybakerAug 26, 2025
Why does my Husqvarna Motorcycle engine overheat?
- C
  Christopher RollinsAug 26, 2025
  If your Husqvarna Motorcycle engine overheats, it could be due to too little coolant in the cooling system (check the cooling system for leakage and the coolant level), too little air stream (switch off engine when stationary), very dirty radiator fins (clean the radiator fins), foam formation in the cooling system (drain and refill the coolant), a damaged cylinder head or cylinder head gasket (check the cylinder head and cylinder head gasket), a bent radiator hose (change the radiator hose), or a defective thermostat (check the thermostat; guideline opening temperature: 70 °C).
M
mmullenAug 28, 2025
What to do if Husqvarna TE 300i Motorcycle engine has no idle?
- R
  Rebecca JohnstonAug 28, 2025
  If your Husqvarna Motorcycle engine has no idle, it could be due to a defective spark plug (change the spark plug), faulty ignition (check the ignition coil, spark plug connector, and stator winding of the alternator), or the idle speed not being set correctly (adjust the idle speed).
R
Roger StrongAug 30, 2025
What to do if my Husqvarna TE 300i engine does not speed up?
- M
  Mary HernandezAug 30, 2025
  If the Husqvarna Motorcycle engine does not speed up, it may be due to a defect in the fuel injection system (read out the fault memory using the Husqvarna Motorcycles diagnostics tool), faulty ignition (check the ignition coil, spark plug connector, and stator winding of the alternator), or the ambient pressure being incorrectly stored (program ambient pressure).
P
Patricia SheltonSep 1, 2025
What causes a Husqvarna Motorcycle engine to die during a trip?
- L
  Leslie JamesSep 1, 2025
  If the Husqvarna Motorcycle engine dies during a trip, it could be due to a lack of fuel (refuel), the engine taking in false air (check that the intake flange is firmly seated), a loose or oxidized connector or ignition coil (clean the connector and treat with contact spray), or incorrectly stored ambient pressure (program ambient pressure).
B
bryanflemingSep 4, 2025
Why is my Husqvarna TE 300i battery discharged?
- S
  Samantha AnthonySep 4, 2025
  If your Husqvarna Motorcycle battery is discharged, it could be because the alternator is not charging it (check the charging voltage and the stator winding of the alternator) or due to an unwanted power consumer (check the open-circuit current).
J
Jeffrey Rodriguez DDSSep 6, 2025
Why is there white smoke emission (steam in exhaust gas) from my Husqvarna TE 300i Motorcycle?
- B
  bakermatthewSep 6, 2025
  White smoke emission (steam in exhaust gas) from your Husqvarna Motorcycle can be caused by a damaged cylinder head or cylinder head gasket (check the cylinder head and cylinder head gasket).
W
Wesley JonesSep 8, 2025
What causes gear oil to exit at the vent hose of my Husqvarna Motorcycle?
- M
  Manuel WoodsSep 8, 2025
  If gear oil exits at the vent hose of your Husqvarna Motorcycle, it is likely due to too much gear oil being added (check the gear oil level).
B
Beverly SchultzSep 12, 2025
What does it mean when the malfunction indicator lamp lights up or flashes on my Husqvarna TE 300i?
- T
  tmartinezSep 12, 2025
  If the malfunction indicator lamp lights up or flashes on your Husqvarna Motorcycle, it indicates a defect in the fuel injection system. Check the cabling for damage and the electrical plug-in connections for corrosion and damage. Also, read out the fault memory using the Husqvarna Motorcycles diagnostics tool.
S
Sierra BrownSep 13, 2025
Why is there water in the gear oil of my Husqvarna Motorcycle?
- J
  juannewtonSep 13, 2025
  If there is water in the gear oil of your Husqvarna Motorcycle, it may be caused by a damaged shaft seal ring or water pump (check the shaft seal ring and water pump).

Summary

2 SAFETY ADVICE

2.1 Use definition, intended use

Defines the intended use of the vehicle for different models.

2.3 Safety advice

Provides general safety instructions and highlights their importance.

2.6 Safe operation

Provides essential safety advice for operating the vehicle.

3 IMPORTANT NOTES

3.4 Service

6 CONTROLS

6.1 Clutch lever

Details the clutch lever's location and automatic adjustment.

6.4 Kill switch (All EU models)

Explains the function and possible states of the kill switch.

6.10 Electric starter button

Explains the electric starter button's location and operation.

7 COMBINATION INSTRUMENT

7.3 Messages on the combination instrument

8 PREPARING FOR USE

8.1 Advice on first use

Provides crucial advice for the initial use of the motorcycle.

8.2 Running in the engine

Gives guidelines for the engine run-in period.

9 RIDING INSTRUCTIONS

9.1 Checks and maintenance measures when preparing for use

Lists pre-ride checks and maintenance tasks.

9.5 Braking

Details braking techniques and warnings for safe operation.

9.8 Refueling

Covers refueling procedures, safety warnings, and fuel specifications.

10 SERVICE SCHEDULE

10.2 Required work

Lists scheduled maintenance tasks based on operating hours.

10.3 Recommended work

11 TUNING THE CHASSIS

11.1 Checking the basic chassis setting with the riders weight

11.3 Adjusting the low-speed compression damping of the shock absorber

11.12 Adjusting the compression damping of the fork

12 SERVICE WORK ON THE CHASSIS

12.11 Checking the play of the steering head bearing

13 BRAKE SYSTEM

13.3 Checking the front brake fluid level

Details how to check the front brake fluid level.

13.6 Changing the front brake linings

Explains how to change the front brake linings.

13.9 Checking the rear brake fluid level

Explains how to check the rear brake fluid level.

14 WHEELS, TIRES

14.1 Removing the front wheel

14.5 Checking the tire condition

14.6 Checking the tire air pressure

15 ELECTRICAL SYSTEM

15.1 Removing the battery

15.4 Changing the main fuse

16 COOLING SYSTEM

16.2 Checking the antifreeze and coolant level

16.5 Refilling with coolant

17 TUNING THE ENGINE

17.1 Checking the play in the throttle cable

17.4 Adjusting the idle speed

17.7 Changing the ignition timing map

18 SERVICE WORK ON THE ENGINE

18.1 Changing the fuel screen

18.2 Checking 2-stroke oil level

18.5 Changing the gear oil

19 CLEANING, CARE

19.2 Checks and maintenance steps for winter operation

20 STORAGE

20.1 Storage

20.2 Preparing for use after storage

22 TECHNICAL DATA

22.1 Engine

Provides technical specifications for the engine.

22.2 Engine tightening torques

Lists tightening torques for various engine components.

22.7 Fork

Lists specifications for the front fork.

22.8 Shock absorber

Lists specifications for the rear shock absorber.

23 SUBSTANCES

Brake fluid DOT 4

Coolant

Husqvarna TE 300i Specifications

General

Engine Type	Single cylinder, 2-stroke
Displacement	293.2 cc
Bore x Stroke	72 mm x 72 mm
Fuel System	Electronic Fuel Injection
Starter	Electric starter
Transmission	6-speed
Cooling System	Liquid cooled
Front Suspension	WP XPLOR-USD, Ø 48 mm
Front Brake	260 mm disc
Rear Brake	220 mm disc
Fuel Capacity	9 L
Seat Height	950 mm
Ground Clearance	370 mm