To Next PageTo Next Page
Need help?Do you have a question about the Husqvarna TE 250 - 310 2011 I.E. and is the answer not in the manual?
General| Year | 2011 |
|---|---|
| Manufacturer | Husqvarna |
| Model | TE 250 - 310 I.E. |
| Category | Motorcycle |
| Displacement | 249.5 cc |
| Fuel System | Electronic Fuel Injection |
| Transmission | 6-speed |
| Fuel Tank Capacity | 8.5 L |
| Starter | Electric |
| Cooling system | Liquid cooling |
| Rear suspension | Monoshock |
| Front brake | Disc brake |
| Rear brake | Disc brake |
| Front suspension | USD fork, 48 mm |
Key information and warnings for motorcycle use and warranty.
Explains warning terms like "Warning", "Caution", and "Note".
Specifies the use of original Husqvarna parts for replacements.
Safety precautions regarding children and the parked motorcycle.
Location and format of the motorcycle's frame serial number.
Details about the 17-digit VIN, including model and year designation.
Identifies and describes various controls on the motorcycle.
Specifications for engine type, cooling, bore, stroke, displacement, and compression ratio.
Details about the fuel system, including type and injection feed.
Gear ratios for primary drive, clutch, transmission, and secondary drive.
Information on ignition system type, spark plug type, and gap.
Details of the telescopic front fork, including stanchion diameter and axle.
Description of the progressive rear shock absorber and wheel stroke.
Specifications of the front and rear brake discs and calipers.
Specifies wheelbase, overall length, width, height, saddle height, ground clearance, and weight.
Lists lubricants, fluids, and quantities for various motorcycle parts.
Operation of the fuel tap on TE-TXCi models.
Fuel system details for TE-TXCi models, noting the absence of a fuel tap.
Information on the side stand and its checks.
Procedure for starting the engine when cold.
Function of the double map button for adjusting engine performance maps.
Explanation of speed display, odometer, and unit conversion.
Details on speed display and clock functions, including setting and resetting.
Information on speed display and trip meter functions, including setup.
Details on speed display, chrono functions, and activation.
Displays speed and digital RPM, including neutral and malfunction indicators.
Location and adjustment of the throttle control.
Location and adjustment of the hydraulic clutch control lever.
Procedure for locking and unlocking the steering on TE models.
Controls for the right handlebar commutator on TE-TXCi models.
Controls for the left handlebar commutator on TE models.
Location of the engine stop button on TC models.
Location and operation of the rear brake control.
Pre-ride inspection checklist to ensure safety and prevent failures.
Recommended procedure for breaking in the engine and new motorcycle.
Periodic checks to be performed while riding or during operation.
Procedure for starting the TC model engine.
Recommendations for starting the engine in cold conditions.
Warnings and instructions for using the kick start pedal.
Recommendations for starting the TE model engine in cold conditions.
Recommendations for starting the TXCi model engine in cold conditions.
Action to take in case of stuck throttle or uncontrollable engine.
Procedures for engine oil change and filter maintenance.
Warning about removing a hot radiator cap.
Importance of checking hoses for cracks, swelling, or hardening.
Notes on throttle cable replacement and reassembly measures.
Interpreting spark plug appearance for correct heat rating.
Caution regarding selecting spark plugs with appropriate heat ranges.
Instructions for washing and cleaning the air filter.
Procedures for reassembling the air filter correctly.
Instructions for washing and cleaning the air filter.
Procedures for reassembling the air filter correctly.
Procedure for checking and adjusting steering wheel play.
Procedure for adjusting and using the steering lock.
Warning about mushy brake lever and potential defects.
Adjustment of the rear brake pedal's idle stroke.
Warning about brake pad wear and total brake ineffectiveness.
Check of the clutch fluid level in the pump reservoir.
Notes on checking oil level and adjusting units for suspension.
Adjustment of fork compression damping.
Adjustment of fork extension damping.
Procedure for bleeding air from the fork.
Procedure for checking and setting the oil level in the fork legs.
Adjusting the handlebar position forward or backward.
Adjusting the handlebar height by changing screws and spacers.
Procedure for adjusting the spring preload of the rear shock absorber.
Warning against disassembling the shock absorber.
Adjustment of compression damping speed for the shock absorber.
Adjustment of extension damping for the shock absorber.
Procedure for fast adjustment of the chain tension.
Procedure for checking chain, pinion, and sprocket wear.
Instructions for lubricating the motorcycle's chain.
Warning against using grease for chain lubrication.
Specific instructions for washing chains with or without OR seals.
Lubrication methods for chains with or without OR seals.
Advice on using new joints when reassembling the chain.
Warning about chain oil contacting tires or brake disc.
Notes on operating the front brake lever and laying down the wheel.
Note on pumping the brake control lever after reassembly.
Notes on operating the rear brake pedal and pumping it after reassembly.
Importance of keeping tires properly inflated.
Overview of major brake components.
Steps for removing brake pads.
Information on inspecting brake pads for wear and service limit.
Instructions for cleaning brake pads and discs.
Procedure for installing new brake pads.
Procedure for measuring brake disc thickness and replacement criteria.
Instructions for accessing the battery and using a battery charger.
Safety warnings regarding battery acid and charging.
Table showing indicative values for battery charging time based on status.
Information that the tail light is an LED light.
Procedure for replacing the number plate lamp bulb.
Post-race inspection checklist and general lubrication.
Recommendations for protecting parts before washing and avoiding high-pressure jets.
