To Next PageTo Next Page
Need help?Do you have a question about the Husqvarna WR 250/2006 and is the answer not in the manual?
General| Year | 2006 |
|---|---|
| Manufacturer | Husqvarna |
| Model | WR 250 |
| Category | Motorcycle |
| Displacement | 249 cc |
| Bore x Stroke | 66.4 mm x 72 mm |
| Compression Ratio | 12.5:1 |
| Cooling System | Liquid-cooled |
| Ignition | CDI |
| Transmission | 6-speed |
| Final Drive | Chain |
| Rear Suspension | Mono shock |
| Front Brake | Single disc |
| Rear Brake | Single disc |
| Front Tire | 90/90-21 |
| Rear Tire | 140/80-18 |
| Engine Type | Single cylinder, two-stroke |
| Fuel System | Carburetor |
| Front Suspension | Inverted fork |
Adjustment of the throttle cable via the adjusting screw on the handlebar or carburetor cover.
Adjustment of the front brake lever position using fixing screws.
Adjustment of the clutch lever free play using the adjusting unit.
Adjustment of the rear brake pedal position relative to the footrest.
Operation of the gear shift lever for engaging gears.
Location and operation of the kickstart pedal.
Specifications for engine type, cooling, bore, stroke, capacity, and compression ratio.
Details the valve type and mechanical control for the exhaust.
Specifies the oil-gasoline mix percentage for the engine during running-in and after.
Details the ignition system type and variable advance.
Provides specifications for the carburetor type, venturi diameter, and jet sizes.
Describes the clutch as a multi-disc type in oil bath.
Specifies the transmission type and gear ratios for all five speeds.
Description of the frame type and material.
Describes the 'Upside Down' fork type with adjustable compression and rebound.
Describes the rear suspension as progressive with a single shock absorber.
Specifies the front brake as a floating disc with hydraulic control.
Specifies the rear brake as a floating disc with hydraulic control.
Lists the front and rear rim types and sizes.
Information on front and rear tires and pressure.
Provides specifications for wheelbase, length, width, height, weight, and capacities.
Description of the digital instrument and warning lights.
Procedure for checking spark advance.
Location and function of the voltage regulator.
Description of the H.T.S. exhaust valves.
Procedures for adjusting the front fork's compression and extension.
Adjustment of the throttle cable.
Adjustment of the front brake lever.
Adjustment of the clutch lever and free play.
Adjustment of the rear brake pedal position.
Operation of the gear shift lever.
Location and operation of the kickstart pedal.
List of checks to perform before riding to prevent accidents or failures.
Procedures for starting the engine (cold and warm).
Procedure for breaking in the engine.
Warnings about the potential dangers of improper brake usage.
Procedure for adjusting the chain tension.
Procedure for lubricating the chain.
Procedure for checking transmission oil level.
Procedure for replacing transmission oil.
Procedure for checking coolant level.
Procedure for replacing cooling fluid.
Procedure for adjusting the throttle cable.
Procedure for adjusting the idle circuit.
Procedure for adjusting the main circuit.
Jet settings based on altitude and temperature.
Procedure for adjusting the clutch.
Measure the thickness of new clutch discs and the wear limit.
Note to replace any spring which does not meet the service specification.
Procedures for adjusting the front fork's compression and extension.
Procedure for adjusting the rear shock absorber's damping.
Procedure for measuring brake disc thickness and checking the service limit.
Procedure for inspecting brake pads for wear and checking the service limit.
Procedure for changing brake fluid.
Procedure for bleeding the front brake system.
Procedure for bleeding the rear brake system.
Procedure for replacing the muffler's deadening material.
Information on cylinder-piston clearance.
Procedure for checking piston ring/groove clearance.
Procedure for inspecting wheels, rims, tires, and spokes.
Procedure for checking and adjusting wheel rim bending.
Description of the ignition system components.
Lists the components of the electrical system.
Procedure for replacing headlamp bulbs.
Procedure for replacing the rear tail light bulb.
Procedures for cleaning and inspecting the motorcycle after racing.
Instructions for preparing the motorcycle for long-term storage.
Warning about tampering with the noise control system.
Maintenance and cleanout instructions for the spark arrester.
