To Next PageTo Next PageWhat does it mean when the PFC module thermal circuit is abnormal in my hydro-s Inverter 16?
If the PFC module thermal circuit is abnormal in your hydro-s Heat Pump, it is likely due to a damaged driver board. To resolve this, replace the driver board and check if the fan motor speed is too low or if the fan motor is damaged; replace it if necessary.
What causes DC fan motor failure in hydro-s Inverter 16 Heat Pump?
DC fan motor failure in your hydro-s Heat Pump can be caused by a damaged DC motor, a damaged main board, or a stuck fan blade. To fix this, test the DC motor and replace it if necessary, replace the main board, and remove any obstruction that is preventing the fan blade from spinning freely.
What should I do if my hydro-s Inverter 16 displays IPM module protection?
IPM module protection in your hydro-s Heat Pump can be triggered by data mistakes, wrong compressor phase connection, compressor liquid and oil accumulation, or damage to the compressor or driver board. To resolve this, turn off the electricity supply and restart after 3 minutes, replace the driver board, and check the compressor sequence connection.
How to troubleshoot controller malfunction in hydro-s Inverter 16?
A controller malfunction in your hydro-s Heat Pump can be caused by poor wire connections, damaged signal wires, or a failure of the controller itself. To address this, check and reconnect the signal wire, replace the signal wire if necessary, turn off the electricity supply and restart the machine, or replace the controller.
What to do for software control exception in hydro-s Heat Pump?
If you are experiencing a software control exception in your hydro-s Heat Pump, it may be due to the compressor running out of step, a wrong program, or impurities inside the compressor causing unstable rotation. To resolve this, check the main board or replace it, and enter the correct program.
How to fix high pressure failure in hydro-s Inverter 16?
A high pressure failure in your hydro-s Heat Pump can occur due to several reasons: a bad connection or failure of the high pressure switch, high ambient or water temperature, low water flow, or abnormal fan motor speed. To resolve this, check the wiring for the high pressure switch, or replace it. Also, check the water flow and water pump, inspect the fan motor, and examine and repair the piping system.
Why does my hydro-s Inverter 16 show VDC voltage too high protection?
VDC voltage too high protection in your hydro-s Heat Pump can be caused by a high mother line voltage or a damaged driver board. To address this, check if the power supply is within the normal range and replace the driver board or main board if necessary.
What triggers PFC module protection in my hydro-s Heat Pump?
PFC module protection in your hydro-s Heat Pump can be triggered by an output exception of the PFC module, a motor issue, a broken fan blade, or abnormal input voltage. To troubleshoot, replace the driver board, check the fan motor speed or replace the fan motor if damaged, replace the fan blade, and check the input voltage.
How to fix communication failure between main board and driver board in hydro-s Inverter 16?
A communication failure between the Main board and driver board in your hydro-s Heat Pump can be caused by a poor connection or damage to the communication wire. To resolve this, check the wire connection and replace the wire if necessary.
What causes communication failure between the controller and main board in hydro-s Inverter 16 Heat Pump?
Communication failure between the controller and the main board in your hydro-s Heat Pump can be caused by a poor signal wire connection or a damaged signal wire, or a controller malfunction. To fix this, check and reconnect the signal wire, replace the signal wire if necessary, turn off the electricity supply and restart the machine, or replace the controller.
Guidance on electrical hookup, initial startup, and condensation management.
Overview of controller buttons, LED indicators, and basic key functions.
Detailed explanation of parameter checking, time settings, and system reset.
Explanation of operating modes (POWER, SMART, SILENT) and related indicator lights.
Comprehensive guide to error codes, their causes, and troubleshooting steps.
Solutions for common issues like no display, incorrect temperature, or water stains.
General
