How to fix four-way valve reversal failure in hydro-s Heat Pump?
Four-way valve reversal failure in your hydro-s Heat Pump can be caused by the valve failing to reverse or a lack of refrigerant. To troubleshoot, switch to cooling mode to check if the 4-way valve has reversed correctly, replace the 4-way valve if necessary, and add refrigerant.
What to do if my hydro-s Inverter 6 shows a low pressure failure?
A low pressure failure in your hydro-s Heat Pump could be due to a bad connection or failure of the low pressure switch, a blocked EEV or jammed pipe system, abnormal motor speed, or gas leakage. To address this, check the wiring for the low pressure switch, or replace it. Inspect the EEV and piping system, check the motor, and use a high pressure gauge to check the pressure value.
Why does my hydro-s Heat Pump show input current over high protection?
An input current over high protection in your hydro-s Heat Pump can be triggered by a compressor current that is too large, abnormal water flow, power fluctuations, or an incorrect PFC inductor. To troubleshoot, check the compressor and the waterway system. Also, verify that the power supply is within the normal range and that the correct PFC inductor is being used.
What causes water temperature (T2) too low protection under cooling mode in my hydro-s Inverter 6 Heat Pump?
Water temperature (T2) too low protection under cooling mode in your hydro-s Heat Pump can be caused by low water flow or an abnormal T2 temperature sensor. To fix this, check the water pump and waterway system and replace the T2 temperature sensor.
What to do if there is an inter-chip communication failure on the main control board of my hydro-s Inverter 6 Heat Pump?
If there is an inter-chip communication failure on the main control board of your hydro-s Heat Pump, turn off the electricity supply and restart it. If the problem persists, replace the main board.
Why does my hydro-s Heat Pump activate antifreeze protection in winter?
Antifreeze protection in your hydro-s Heat Pump activates in winter when the ambient temperature or water inlet temperature is too low. This is normal protection.
What should I do if my hydro-s Inverter 6 displays IPM module protection?
IPM module protection in your hydro-s Heat Pump can be triggered by data mistakes, wrong compressor phase connection, compressor liquid and oil accumulation, or damage to the compressor or driver board. To resolve this, turn off the electricity supply and restart after 3 minutes, replace the driver board, and check the compressor sequence connection.
What causes DC fan motor failure in hydro-s Inverter 6?
DC fan motor failure in your hydro-s Heat Pump can be caused by a damaged DC motor, a damaged main board, or a stuck fan blade. To fix this, test the DC motor and replace it if necessary, replace the main board, and remove any obstruction that is preventing the fan blade from spinning freely.
What triggers low ambient temperature protection in my hydro-s Heat Pump?
Low ambient temperature protection in your hydro-s Heat Pump can be triggered when the unit is used outside of its intended environment or if there is a sensor abnormality. To resolve this, stop using the unit if it is beyond its intended scope, or replace the sensor.
Why is the temperature of the IPM module too high in my hydro-s Inverter 6?
If the temperature of the IPM module is too high in your hydro-s Heat Pump, it could be due to an output exception of the IPM module thermal circuit, a motor issue, or a broken fan blade. To solve this, replace the driver board, check the fan motor speed or replace the fan motor if damaged, and replace the fan blade.
Detailed technical specifications for various Hydro-S Inverter models.
Further technical specifications for Hydro-S Inverter pool heat pumps.
Guidance on correctly connecting the heat pump to the power supply.
Step-by-step instructions for the initial startup and operation.
Wiring diagram for the swimming pool heat pump models.
Overview of the controller's keys and their functions.
List of error codes, malfunctions, reasons, and solutions.
Solutions for malfunctions without error codes on the LED controller.
To Next Page
General
