Hypex Electronics warrants this device for a period of
two years after the original date of purchase against
defects due to faulty workmanship or materials
arising from Normal Use of the device. The warranty
covers working parts that affect the function of the
device. It does NOT cover cosmetic deterioration
caused by fair wear and tear, or damage caused by
accident, misuse or neglect. Any attempt to modify or
take apart the device (or its accessories) will void the
warranty.
If you discover a defect, notify Hypex Electronics
during the warranty period. Claims under warranty
must be supported by reasonable evidence that the
date of the claim is within the warranty period. To
validate your warranty, please keep your original
purchase receipt together with these warranty
conditions for the duration of the warranty period.
Replacement products claimed under warranty are
not entitled to renewed 2-year warranty coverage.
Date of purchase:
Limited Warranty Revisions
Notes
Hypex Electronics BV, its affiliates, agents, and
employees, and all persons acting on its or their behalf
(collectively,“Hypex Electronics”), disclaim any and
all liability for any errors, inaccura cies or
incompleteness contained in any datasheet or in any
other disclosure relating to any product.
This subassembly is designed for use in music
reproduction equipment only. No representations are
made as to fitness for other uses. Except where noted
otherwise any specifications given pertain to this
subassembly only. Responsibility for verifying the
performance, safety, reliability and compliance with
legal standards of end products using this
subassembly falls to the manufacturer of said end
product.
LIFE SUPPORT POLICY: Use of Hypex products in life
support equipment or equipment whose failure can
reasonably be expected to result in injury or death is
not permitted except by explicit written consent from
Hypex Electronics BV.
Disclaimer
19
No power:
Ÿ Check the power outlet
Ÿ The internal fuse may be blown. This fuse is not
user replaceable. Please contact Hypex
Electronics for more information about service
and repair.
No Sound
Ÿ A protection might be triggered. Is the module
overheated?
Ÿ Verify the gain settings.
Ÿ Is the DSP muted?
Ÿ Check the source signal.
Ÿ Check the cables.
Ÿ Is there a filter installed in the DSP?
Poor sound or noise
Ÿ Check your filters
Ÿ Check if the signal is not inverted. Inverted
signals might cause one of your woofers to be
out-of-phase.
Ÿ Clip?
Ÿ Check all connections.
Hum
Use balanced connections for best system
performance.
Troubleshooting
We continuously work to improve your experience
with the FusionAmp. If you have suggestions, remarks
or found a bug, please contact us.
If you have problems with your FusionAmp, please
first make sure your have the latest version of HFD
and you have updated the firmware of your
FusionAmp. If you need to update your firmware,
please follow the instruction carefully.
Do you need additional assistance with assembling or
configuring your FusionAmp?
Visit our website!
The latest datasheets, manuals, 3D models can be
found there. Look into our FAQ and if you can not find
the answer there, you can also contact us and we will
be happy to assist you!
Support
Frequently asked questions
Why is there not a FusionAmp with one
Q
NC250MP or NC500MP, with an additional
NC100HF?
Since the FA123 and FA253 can be configured in
A BTL, one can achieve the same result with better
audio performance with these models. In
addition, e.g. a NC250MP with NC100HF would
result in a larger plate compared to a FA252,
whilst having a lower specification.
Q
The DSP used in the FusionAmp is capable of
processing FIR filters, why is this not supported
in the FusionAmp?
The DSP used in the FusionAmp does indeed
A support FIR filtering, however due to several
design choices and internal software functions, a
percentage of the processing capabilities of the
DSP is reserved. Because of this, the remaining
amount of resources are too limited for a FIR
filter of proper use.
18
To Next Page
Loading...
