Genuine Accessories
Electronic Installation Instructions
Glasses Gloves
Mask Hearing Protection
Part Weight (Gross) FMVSS 110 Compliance Information
Technical Support
1
Read the entire Installation Instructions
rior to be
innin
the installation of the
art.
2
3
Make sure the vehicle is com
letel
clean and dr
in the area
s
the
art is to be installed.
4
Ensure the vehicle is
ro
erl
rotected in the area
s
that the accessor
is to be installed.
5
NEVER
lace tools on
ainted surfaces, seatin
surfaces, dash
ad, console or floor car
et/mats.
6
lwa
s wear a
ro
riate
ersonal
rotective e
ui
ment, includin
loves, safet
lasses, etc., when re
uired.
7
Record radio
resets
rior to disconnectin
batter
ower, if needed.
8
Roll down the driver's window and ad
ust the
ower seats
if a
licable
rior to disconnectin
batter
ower, if needed.
9
To prevent stress on the remote start wire harness, ensure the tilt steering column is
ully extended be
ore installing the kit.
10)
Ensure Transportation Switch is switched to 'ON' on the fuse box.
11)
Vehicle should be at room temperature.
12)
Language English
6/5/2020Rev. Date
Accessory:Vehicle Model:
Difficulty stated above reflects the minimum level of
expertise required to install the accessory:
( B )
Remote Engine Start - Key Start
(A) Customer
Venue
Difficulty:
Part No.
Model Year
Copy OEM Logo Here (→)
2020~
K2F57 AC000
Note:
(B) Dealer Technician
Instructional Symbols / Definitions
Application Notes
Denotes quality processes to be checked
prior to moving to the next step
Denotes personal protective equipment (PPEs) that
may be required for a step. Examples of safety
equipment icons noted below:
Denotes cautions to be taken to avoid
vehicle and component damage
Ratchet 12mm Socket10mm Socket Extension
Basic Required Tools
Vehicle must be equipped with mechanical key start.
Ensure vehicle does NOT
have SMART KEY (PUSH BUTTON IGNITION SYSTEM).
Vehicle should be equipped with automatic transmission, power door locks, and power windows. If these features are not equipped on the vehicle, do not proceed with install.
Denotes warnings that may lead to
serious physical injury or vehicle damage
#2 Phillips
Screwdriver
(C) Master Technician or Specialist
Authorized dealers use:
Hours:
Clip Removal Tool Trim Removal Tool Clean Cloth
50/50 Isopropyl
Alcohol (70%) and
Water Mix
N
O
T
E
Denotes important information to be
reviewed during the step
Denotes specific tools that are necessary
to complete a step
Notes to the installer:
Pliers
(1) 855-225-7344
M~F - 9am~5pm Pacific Standard Time
If this is a printed copy of the installation instructions, ensure you have the latest revision by
scanning the QR code or by entering the website address listed below before beginning
installation. Use the latest revision date as noted by “Rev. Date” above.
www.hyundaiaccessories.com/admin_media_uploads/installationSheets/k2f57_ac000.pdf
1.32
lbs
All dealers must determine if the Net weight they have added in the form of all options or accessories, when added to the weight of all Port/Dealer
Installed options or accessories, exceeds the lesser of 1.5% of GVWR or 100 lbs. If the additional weight does exceed the lesser of the indicated
thresholds, a “Load Carrying Capacity Reduced” label must be installed. A black, fine-point, indelible marker must be used to write by hand onto the
label, the reduced carrying capacity in kilograms or pounds, which is the total weight of all added options and accessories.
Load Label Part Number: NP070 - 09003
0.60
kg
If applicable, scan the barcode label located on the accessory part or packaging prior to installing, to register the part. If this accessory is installed as
a replacement, register the removal of the old part before registering the new part. Old and new parts will have different barcode data, and the old
re
istration cannot be reused.
Denotes cautions to be taken to avoid
physical injury or electronic component
damage
The order of the disassembly and reassembly steps have been optimized for maximum efficiency and the correct installation of the Remote Engine Start
kit. Disassemble vehicle components (including harness connectors) and install the kit components according to each step, as indicated. Avoid
disassemblin
or reassemblin
an
com
onents in advance to
revent unnecessar
labor time and/or installation errors.
Torque Wrench Wire Cutters
Revision Date
06/05/2020
Page 1 of 13