Hyundai L0F62 AU000 User Manual (English)

To Next Page

Genuine Accessories

Electronic Installation Instructions

Glasses Gloves

Mask Hearing Protection

Part Weight (Gross) FMVSS 110 Compliance Information

Part Weight (Net)

1) Read the entire Installation Instructions prior to beginning the installation of the part.

3) Make sure the vehicle is completely clean and dry in the area(s) the part is to be installed.

4) Ensure the vehicle is properly protected in the area(s) that the accessory is to be installed.

5) NEVER place tools on painted surfaces, seating surfaces, dash pad, console or floor carpet/mats.

6) Always wear appropriate personal protective equipment, including gloves, safety glasses, etc., when required.

7) Record radio presets prior to disconnecting battery, if needed.

8) Roll down the driver's window and adjust the power seats (if applicable) prior to disconnecting battery power, if needed.

)

10mm Socket

Basic Required Tools

Denotes cautions to be taken to avoid

vehicle and component damage

(B) Dealer Technician

Denotes warnings that may lead to

serious physical injury or vehicle damage

Denotes quality processes to be checked

prior to moving to the next step

Denotes personal protective equipment (PPEs) that

may be required for a step. Examples of safety

equipment icons noted below:

Ratchet Extension Pliers 12mm Socket T20 Torx Socket

#2 Phillips

Screwdriver

Entered by

MPA

Tape Measure T20 Torx Driver

Nylon Panel

Removal Tool

Torque Wrench Side Cutters

Denotes important information to be

reviewed during the step

If this is a printed copy of the installation instructions, ensure you have the latest revision by

scanning the QR code or by entering the website address listed below before beginning

installation. Use the latest revision date as noted by “Rev. Date” above.

www.hyundaiaccessories.com/admin_media_uploads/installationSheets/l0f62_au000.pdf

Instructional Symbols / Definitions

Denotes cautions to be taken to avoid

physical injury or electronic component

damage

Denotes specific tools that are necessary

to complete a step

Copy OEM Logo Here (→)

Vehicle Model: Sonata Accessory: Mirror, Auto-Dimming w/ HL5

Model Year 2020~ Difficulty: ( B )

Part No. L0F62 AU000 (DIO)

L0F62 AU600 (PIO)

Note: Difficulty stated above reflects the minimum level of

expertise required to install the accessory:

Language English

Rev. Date 3/3/2020

(A) Customer

10mm Deep Well

Socket

10mm Combination

Wrench

1.10

lbs

Universal Joint

Ensure the parking brake is set and foot is on the brake pedal while function checking.

All dealers must determine if the Net weight they have added in the form of all options or accessories, when added to the weight of all Port/Dealer Installed

options or accessories, exceeds the lesser of 1.5% of GVWR or 100 lbs. If the additional weight does exceed the lesser of the indicated thresholds, a “Load

Carrying Capacity Reduced” label must be installed. A black, fine-point, indelible marker must be used to write by hand onto the label, the reduced carrying

capacity in kilograms or pounds, which is the total weight of all added options and accessories.

Load Label Part Number: NP070 - 09003

0.50

0.75

lbs

0.34

Notes to the installer:

Factory wire harness colors are subject to change. Please use the specified pin number in the harness connector to identify

the correct wire for T-Ta

installation.

If applicable, scan the barcode label located on the accessory part or packaging prior to installing, to register the part. If this accessory is installed as

a replacement, register the removal of the old part before registering the new part. Old and new parts will have different barcode data, and the old

registration cannot be reused.

T20

M12

T20

M10

Revision Date

03/03/2020

Page 1 of 16