ICON EDGE - Error Messages and Troubleshooting

ICON EDGE USER MANUAL
31
11. ERROR MESSAGES
When you turn on the device, it will first perform a reset. The display may show ”Err channel is XX” should
there be problems with one or more functions. “XX” stands for channel 1, 2, 3, 4, 5, 6 etc whose sensor has
encountered a problem. For example, when the display shows “Err channel is Pan movement”, it means
there is an error on channel 1. If there are errors on channel 1, channel 3, channel 6 at the same time, you
may see the error message, “Err channel is Pan movement”, “Err channel is Tilt movement”“ “Err channel is
Shutter” ,flash twice, and then the device will generate a second reset. If the error messages persist after
performing a reset more than twice, the channels which have errors may not work properly however, all
other functions can work as usual. Please contact your dealer or manufacturer for service. Self repair is not
allowed.
PAN- movement Er
(PAN- yoke movement error) This message will appear after the reset of the fixture if the yoke’s
magnetic-indexing circuit malfunction (Optical Sensor or Magnetic Sensor fails) or the stepper motor is
defective (or its driving IC on the main PCB). The PAN- movement is not located in the default position after
the reset.
TILT- movement Er
(TILT- head movement error) This message will appear after the reset of the fixture if the head’s
magnetic-indexing circuit malfunctions ((Optical Sensor or Magnetic Sensor fails)) or the stepper motor is
defective (or its driving IC on the main PCB). The TILT- movement is not located in the default position after
the reset.
CMY wheel Er
(CMY wheel- error) This message will appear after the reset of the fixture if the head’s magnetic-indexing
circuit malfunctions (sensor failed or magnet missing) or the stepper motor is defective (or its driving IC on
the main PCB). The CMY - movement is not located in the default position after the reset.
CTO wheel Er
(CTO wheel- error) This message will appear after the reset of the fixture if the head’s magnetic-indexing
circuit malfunctions (sensor failed or magnet missing) or the stepper motor is defective (or its driving IC on
the main PCB). The CMY - movement is not located in the default position after the reset.
COLOR wheel Er
(COLOR wheel- error) This message will appear after the reset of the fixture if the head’s
magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the stepper motor is defective
(or its driving IC on the main PCB). The COLOR - movement is not located in the default position after the
reset.
GOBO wheel Er
(GOBO wheel- error) This message will appear after the reset of the fixture if the head’s magnetic-indexing
circuit malfunctions (sensor failed or magnet missing) or the stepper motor is defective (or its driving IC on
the main PCB). The GOBO1 - movement is not located in the default position after the reset.
GOBO_R wheel Er
(GOBO_R wheel- error) This message will appear after the reset of the fixture if the head’s
magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the stepper motor is defective
(or its driving IC on the main PCB). The GOBO1_R - movement is not located in the default position after
the reset.
Dimmer wheel Er
(Dimmer wheel- error) This message will appear after the reset of the fixture if the head’s
magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the stepper motor is defective
(or its driving IC on the main PCB). The GOBO2- movement is not located in the default position after the
reset.
Fix Gobo wheel Er
(Fix Gobo wheel- error) This message will appear after the reset of the fixture if the head’s
magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the stepper motor is defective
(or its driving IC on the main PCB). The GOBO2- movement is not located in the default position after the