ID Lock 202 MULTI - User Manual

idlock.no/zwave
ID Lock 202 Multi
Z-Wave Module (FW 1.6)
English User Manual
• Open the door
• Remove batteries from the lock
• Place the module in the tray for “Remote
Control” (see illustration 1)
• Insert batteries
• Activate “Add node” in the gateway app
Follow the instructions in the gateway manual
• Hold key button (3 secs) to activate panel
• Enter [Master PIN], followed by [*]
o Master PIN is created upon setup
• Enter digit [9], followed by [*]
• Enter digit [1]
• Open the door
• Activate “Remove node” in the gateway app
Follow the instructions for your gateway
• Hold key button (3 secs) to activate panel
• Enter [Master PIN], followed by [*]
o Master PIN is created upon setup
• Enter digit [9], followed by [*]
• Enter digit [1]
• Open the door
• Hold key button (3 secs) to activate panel
• Enter [Master PIN], followed by [*]
o Master PIN is created upon setup
• Enter digit [9], followed by [*]
• Enter digit [0]
NB! If the module resets while it is included with a
gateway, the door lock will factory reset. To prevent
this, remove (exclude) the lock first (see: “Remove
the lock”).
Technical specs for the Z-Wave module is listed on the
next page.
Correct communication mode is activated when
batteries are inserted (v1.6 only).
The batteries must be removed before the Z-Wave
Module is inserted or removed. Failing to do so can
cause damage on the module and/or the lock.
1: Place the module in the tray (A) «Remote
Module» when batteries are removed.
Adding the lock (Inclusion)
Remove the lock (Exclusion)
Reset the module (Z-Wave Local Reset)
Technical details
Warning!

Summary

Adding the Lock (Inclusion)

Place Module for Remote Control

Positioning the Z-Wave module into the tray for "Remote Control" functionality.

Initiate Inclusion via Gateway App

Activating the "Add node" function within the gateway application to start inclusion.

Activate Panel and Enter PIN

Holding the key button to activate the panel and entering the Master PIN for authentication.

Complete Inclusion Sequence

Entering specific digits (9 and 1) followed by [*] to finalize the inclusion process.

Removing the Lock (Exclusion)

Initiate Exclusion via Gateway App

Activating the "Remove node" function in the gateway application to begin exclusion.

Activate Panel and Enter PIN

Holding the key button to activate the panel and entering the Master PIN for authentication.

Complete Exclusion Sequence

Entering specific digits (9 and 1) followed by [*] to finalize the exclusion process.

Z-Wave Local Reset Procedure

Activate Panel and Enter PIN

Holding the key button to activate the panel and entering the Master PIN for authentication.

Complete Reset Sequence

Entering specific digits (9 and 0) followed by [*] to initiate the local reset.

Important Reset Warning

Note on factory reset if module is included with gateway; exclude first.

Technical Specifications and Warnings

Technical Details

Technical specifications for the Z-Wave module are listed on the next page.

Communication Mode Activation

Correct communication mode is activated when batteries are inserted (v1.6 only).

Battery Insertion;Removal Warning

Warning: Batteries must be removed before module insertion/removal to prevent damage.

Supported Command Classes and Configuration

Non-Secure Command Classes

List of non-secure Z-Wave command classes supported by the module.

Secure Command Classes

List of secure Z-Wave command classes supported by the module.

Configuration Parameters

Details of configurable parameters for the Z-Wave module, including Lock Mode and RFID Mode.

Notification Parameters

Parameters related to Z-Wave notifications, including access control and emergency events.

User Code Management

Information on managing user codes, RFID key fobs, Service PIN, and Master PIN.

Version Information

Details on Z-Wave protocol library, versions, and hardware specifications.

ID Lock 202 MULTI Specifications

General

Product Type	Smart Door Lock
Connectivity	Bluetooth, Z-Wave
Power Source	Battery
Battery Life	Up to 12 months
Battery Type	4 x AA
Material	Plastic
Security Features	Tamper Alarm
Compatibility	Android, iOS