IDEC MicroSmart Pentra FC5A Series - User Manual

343 pages

Save Page as PDF

To Next Page

FC5A

SERIES

FC9Y-B1273(1)

User’s Manual Advanced Volume

Main Page

Table of Contents9
Table of10
Able of Ontents14
Basic Instruction List15
Advanced Instruction List17
Advanced Instruction Applicable CPU Modules20
Structure of an Advanced Instruction23
Input Condition for Advanced Instructions23
Source and Destination Devices23
Using Timer or Counter as Source Device23
Using Timer or Counter as Destination Device23
Data Types for Advanced Instructions (Integer Type)24
Discontinuity of Device Areas26
NOP (no Operation)26
MOV (Move)27
MOVN (Move Not)31
IMOV (Indirect Move)32
IMOVN (Indirect Move Not)34
BMOV (Block Move)35
IBMV (Indirect Bit Move)36
IBMVN (Indirect Bit Move Not)38
NSET (N Data Set)39
NRS (N Data Repeat Set)40
XCHG (Exchange)41
TCCST (Timer/Counter Current Value Store)42
CMP= (Compare Equal To)43
CMP<> (Compare Unequal To)43
CMP< (Compare Less Than)43
CMP> (Compare Greater Than)43
CMP<= (Compare Less than or Equal To)43
CMP>= (Compare Greater than or Equal To)44
ICMP>= (Interval Compare Greater than or Equal To)48
LC= (Load Compare Equal To)50
LC<> (Load Compare Unequal To)50
LC< (Load Compare Less Than)50
LC> (Load Compare Greater Than)50
LC<= (Load Compare Less than or Equal To)50
LC>= (Load Compare Greater than or Equal To)50
ADD (Addition)53
SUB (Subtraction)53
MUL (Multiplication)53
DIV (Division)53
INC (Increment)65
DEC (Decrement)65
ROOT (Root)67
SUM (Sum)68
RNDM (Random)71
ANDW (and Word)73
ORW (or Word)73
XORW (Exclusive or Word)73
SFTL (Shift Left)77
SFTR (Shift Right)79
BCDLS (BCD Left Shift)81
WSFT (Word Shift)83
ROTL (Rotate Left)84
ROTR (Rotate Right)86
Data Conversion Instructions89
HTOB (Hex to BCD)89
BTOH (BCD to Hex)91
HTOA (Hex to ASCII)93
ATOH (ASCII to Hex)95
BTOA (BCD to ASCII)97
ATOB (ASCII to BCD)100
ENCO (Encode)103
DECO (Decode)104
BCNT (Bit Count)105
ALT (Alternate Output)106
CVDT (Convert Data Type)107
DTDV (Data Divide)109
DTCB (Data Combine)110
SWAP (Data Swap)111
WKTIM (Week Timer)113
WKTBL (Week Table)114
Using Clock Cartridge117
Setting Calendar/Clock Using Windldr118
Setting Calendar/Clock Using a User Program118
Adjusting Clock Using a User Program119
Adjusting Clock Cartridge Accuracy120
DISP (Display)121
DGRD (Digital Read)123
LABEL (Label)125
LJMP (Label Jump)125
LCAL (Label Call)127
LRET (Label Return)127
DJNZ (Decrement Jump Non-Zero)129
DI (Disable Interrupt)131
EI (Enable Interrupt)131
IOREF (I/O Refresh)133
HSCRF (High-Speed Counter Refresh)135
FRQRF (Frequency Measurement Refresh)136
COMRF (Communication Refresh)137
XYFS (XY Format Set)139
CVXTY (Convert X to Y)140
CVYTX (Convert y to X)141
AVRG (Average)145
PULS1 (Pulse Output 1)148
PULS2 (Pulse Output 2)148
PULS3 (Pulse Output 3)148
PWM1 (Pulse Width Modulation 1)154
PWM2 (Pulse Width Modulation 2)154
PWM3 (Pulse Width Modulation 3)154
RAMP1 (Ramp Control 1)160
RAMP2 (Ramp Control 2)160
ZRN1 (Zero Return 1)172
ZRN2 (Zero Return 2)172
ZRN3 (Zero Return 3)172
PID (PID Control)179
Application Examples196
DTML (1-Sec Dual Timer)203
DTIM (100-Ms Dual Timer)203
DTMH (10-Ms Dual Timer)203
DTMS (1-Ms Dual Timer)203
TTIM (Teaching Timer)205
RUNA READ (Run Access Read)208
RUNA WRITE (Run Access Write)209
STPA READ (Stop Access Read)210
STPA WRITE (Stop Access Write)211
RAD (Degree to Radian)215
DEG (Radian to Degree)216
SIN (Sine)217
COS (Cosine)218
TAN (Tangent)219
ASIN (Arc Sine)220
ACOS (Arc Cosine)221
ATAN (Arc Tangent)222
LOGE (Natural Logarithm)223
LOG10 (Common Logarithm)224
EXP (Exponent)225
POW (Power)226
FIFOF (FIFO Format)227
FIEX (First-In Execute)229
FOEX (First-Out Execute)229
NDSRC (N Data Search)231
TADD (Time Addition)233
TSUB (Time Subtraction)237
HTOS (HMS to Sec)241
STOH (Sec to HMS)242
HOUR (Hour Meter)243
Computer Link System Setup (1:N Computer Link System)245
Programming Windldr246
Monitoring PLC Status247
System Setup249
Applicable Modems250
Special Internal Relays for Modem Mode250
Special Data Registers for Modem Mode251
Originate Mode251
Disconnect Mode253
AT General Command Mode253
Answer Mode254
Modem Mode Status Data Register255
Initialization String Commands256
Preparations for Using Modem257
Programming Data Registers and Internal Relays257
Setting up the CPU Module257
Programming Windldr258
Operating Procedure for Modem Mode259
Sample Program for Modem Originate Mode260
Sample Program for Modem Answer Mode261
Troubleshooting in Modem Communication262
Modbus TCP Communication General Information263
Modbus TCP Master Communication264
Modbus TCP Slave Communication267
Programming the Web Server Module (FC4A-SX5ES1E)270
Modbus TCP Communication Format271
About AS-Interface273
Operation Basics278
Pushbuttons and LED Indicators286
AS-Interface Devices290
Using Two AS-Interface Master Modules304
Using Windldr306
Switchnet Data I/O Port (AS-Interface Master Module 1)311
Allocating Communication Port Number317
Computer Link Communication318

Need help?

Do you have a question about the IDEC MicroSmart Pentra FC5A Series and is the answer not in the manual?

IDEC MicroSmart Pentra FC5A Series Specifications

General

Brand	IDEC
Model	MicroSmart Pentra FC5A Series
Category	Controller
Language	English

Related product manuals

IDEC MICRO3

235 pages

IDEC SmartAXIS Touch FT1A Series

IDEC MicroSmart Pentra FC5A Series - User Manual

Table of Contents

IDEC MicroSmart Pentra FC5A Series Specifications

Related product manuals