Idex HALE MIV 2.0

Brand	Idex
Model	HALE MIV 2.0
Category	Control Unit
Language	English

Abbreviations And Acronyms

ID

Identification

MIV

Master Intake Valve

NFPA

National Fire Protection Association

OEM

Original Equipment Manufacturer

OIM

Operation Installation Maintenance

PN

Part Number

PPE

Personal Protection Equipment

R&R

Removal and Replacement

SAE

Society of American Engineers

SCR

Symptom, Cause, Remedy

AHJ

Authority Having Jurisdiction

FAST

Factory Authorized Service Team

1. SAFETY

1.1. Safety Headings

Defines DANGER, WARNING, CAUTION, NOTICE symbols.

1.2. Safety Summary

Lists all WARNINGS and CAUTIONS used in the manual.

1.3. PPE

Lists minimum Personal Protection Equipment for maintenance.

2. INTRODUCTION

2.1. Overview

Provides an overview of the Hale Master Intake Valve (MIV).

2.2. Installation

Details the installation process for the Hale Master Intake Valve.

2.2.1 Mounting of Side Suction Valves

Instructions for mounting side suction valves.

2.2.2 Mounting of Bottom (FrontRear) Suction Valves

Instructions for mounting bottom/front/rear suction valves.

2.2.3 Plumbing Relief Valve

Procedures for plumbing the relief valve.

2.2.4 Suction Hose Water Drain

Instructions for suction hose water drain.

2.2.5 Air Bleeder Valve

Instructions for installing the air bleeder valve.

2.2.6 Suction Hose Priming

Instructions for suction hose priming.

2.2.7 Panel Placard, Handwheel and Handwheel Extension

Mounting panel placards, handwheels, and extensions.

2.2.8 Relief Valve Adjustment

Procedures for adjusting the relief valve.

2.2.9 Rotation of Gearbox (if necessary)

Instructions for rotating the gearbox.

2.3. How To Use This Manual

Guidance on using the manual and its sections.

2.4. Disclaimer

Policy on continuous development and amendments.

2.5. Principles Of Operation

Principles of operation for communication.

2.5.1 Air Bleeder Valve

Operation of the air bleeder valve.

2.5.2 Electric Motor Operated Valve (HALE MIV-E)

Operation of the electric motor operated valve.

2.5.3 Manual Handwheel Operated Valve (HALE MIV-M)

Operation of the manual handwheel operated valve.

2.5.4 Manual Override (Electric Operated Valve Only)

Manual override for electric operated valves.

2.5.5 Cold Weather Operation

Procedures for cold weather operation.

3. PREVENTIVE MAINTENANCE

3.1. MIV Disc Lubrication

Instructions for lubricating the MIV disc.

4. CORRECTIVE MAINTENANCE

4.1. General Repair Guidelines

General guidelines for repair procedures.

4.1.1 Recommended Tools

Lists recommended tools for maintenance.

4.1.2 Recommended Cleaners

Lists recommended cleaning agents.

4.1.3 Recommended Lubricants

Lists recommended lubricants.

4.1.4 Thread Lock And Sealant Compounds

Lists thread lock and sealant compounds.

4.2. Cleaning and Inspection Guidelines

Guidelines for cleaning and inspection.

4.2.1 Cleaning Required for Thread Lock Compounds

Cleaning procedures for thread lock compounds.

4.3. Removal and Replacement Guidelines

Guidelines for removal and replacement.

4.3.1 Match Mark or Note Component Orientation

Procedures for marking component orientation.

4.4. Troubleshooting

System troubleshooting procedures.

4.4.1 General Testing MIV-E Valves for Proper Operation

Testing procedures for MIV-E valve electrical operation.

4.5. MIV Component Bench Procedures

Bench repair procedures for MIV components.

4.5.1 Valve Disc Replacement

Bench procedure for valve disc replacement.

4.5.2 Switch Replacement Bench Procedure

Bench procedure for switch replacement.

4.5.3 Relief Valve Component Replacement

Procedures for replacing relief valve components.

4.5.4 Bench Procedure for MIV Control Module Replacement

Bench procedure for control module replacement.

5. PARTS LIST

6. INSTALLATION DRAWING

APPENDIX A. MANUFACTURERS INFORMATION

A.1. MANUFACTURERS INFORMATION

Contact information for Hale Products and Godiva LTD.

A.2. WARRANTY

Information on product warranty and procedures.

Table of Contents

Questions and Answers:

Idex HALE MIV 2.0 Specifications

Summary