Why is my IKEA SKINANDE Dishwasher not filling with water?
If your IKEA dishwasher isn't filling with water and the display shows an error, ensure the water tap is fully open and that the water supply pressure isn't too low. Check that the water tap isn't clogged and that the filter in the inlet hose is clean and free from obstructions. Also, make sure the inlet hose has no kinks or bends.
Why does the salt indicator stay on in my IKEA SKINANDE Dishwasher?
If the salt indicator on your IKEA dishwasher stays on after refilling the salt container, and persists after 3 or 4 cycles, contact the service. This might happen if you're using salt that takes longer to dissolve.
How to remove streaks from my IKEA SKINANDE Dishwasher?
If you notice whitish streaks or bluish layers on glasses and dishes from your IKEA dishwasher, the release quantity of rinse aid may be too high. Try adjusting the rinse aid level to a lower setting. Also, the quantity of detergent may be too much.
How to prevent stains on dishes in my IKEA Dishwasher?
If your IKEA dishwasher leaves stains and dry water drops on glasses and dishes, the released quantity of rinse aid may not be sufficient. Adjust the rinse aid level to a higher setting. Also, the quality of the rinse aid could be the cause.
Why are the dishes wet after using my IKEA SKINANDE Dishwasher?
If the dishes are wet after a cycle in your IKEA dishwasher, it could be that the selected program does not have a drying phase or has one with a low temperature. Check if the rinse aid dispenser is empty. The quality of the rinse aid or multi-tablets might also be the cause. Try a different brand or use rinse aid and multi-tablets together. You can also keep the dishwasher door ajar for a while before removing the tableware.
Why is the interior of my IKEA SKINANDE wet?
If the interior of your IKEA dishwasher is wet, it is not a defect. It is caused by humidity in the air condensing on the walls.
What to do if my IKEA SKINANDE Dishwasher does not fill with water?
If your IKEA Dishwasher isn't filling with water, check the following: * Ensure the water tap is fully open. * Verify the water supply pressure is adequate. * Make sure the water tap isn't clogged. * Clean the filter in the inlet hose if it's clogged. * Confirm that the inlet hose has no kinks or bends.
Why I cannot activate my IKEA SKINANDE Dishwasher?
If you cannot activate your IKEA Dishwasher, make sure that the mains plug is properly connected to the mains socket and check the fuse box for any damaged fuses.
Why are my dishes wet after using the IKEA Dishwasher?
If your dishes are wet after using the IKEA Dishwasher, it could be due to several reasons: * The selected program may not have a drying phase or uses a low-temperature drying phase. * The rinse aid dispenser might be empty. * The quality of the rinse aid could be a factor. * The multi-tablets you're using might not be suitable. Try a different brand, or activate the rinse aid dispenser and use rinse aid along with the multi-tablets.
What to do if IKEA SKINANDE does not fill with water?
If your IKEA Dishwasher isn't filling with water, consider these potential causes: * Ensure the water tap is fully open. If it's closed, open it. * Check for clogs or limescale on the water tap; clean it if necessary. * Inspect the filter in the water inlet hose for clogs and clean it. * Make sure the water inlet hose isn't kinked or bent; correct its position if needed. * If the anti-flood device is activated due to water leakages, close the water tap and contact the service.
General| Type | Built-in |
|---|---|
| Capacity | 13 place settings |
| Noise Level | 44 dB |
| Number of Programs | 6 |
| Child Lock | Yes |
| Delay Start | Yes |
Safety guidelines for children and vulnerable individuals using the appliance.
Instructions for the safe and correct installation of the appliance.
Information on earthing, socket types, and cable safety for electrical connection.
Details on connecting the appliance to the water supply and checking for leaks.
Precautions to follow during the appliance's operation.
Solutions for when the appliance fails to power on.
Causes and solutions for the appliance not taking in water.
Troubleshooting steps if the appliance does not begin its cycle.
Steps to resolve issues with the appliance not draining water.
Information when the anti-flood protection is activated.
Explains why the appliance may stop and start intermittently.
Possible reasons for programmes exceeding their expected duration.
Explanation for the remaining time display behaving erratically.
Troubleshooting minor water leaks from the appliance door.
Solutions for a stiff or hard-to-close appliance door.
Identifies causes for unusual noises originating from within the appliance.
Reasons why the appliance might trip the household circuit breaker.
To Next Page
