Ikra ICMT 2/20 - Specified Conditions of Use

41
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instrucons to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condion that may aect the power
tool’s operaon. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cung tools sharp and clean. Properly
maintained cung tools with sharp cung edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.
in accordance with these instrucons, taking into
account the working condions and the work to
be performed. Use of the power tool for operaons
dierent from those intended could result in a
hazardous situaon.
5) Baery tool use and care
a) Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one
type of baery pack may create a risk of re when
used with another baery pack.
b) Use power tools only with specically designated
baery packs. Use of any other baery packs may
create a risk of injury and re.
c) When baery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connecon from one terminal to another.
Shorng the baery terminals together may cause
burns or a re.
d) Under abusive condions, liquid may be ejected
from the baery; avoid contact. If contact
accidentally occurs, ush with water. If liquid
contacts eyes, addionally seek medical help.
Liquid ejected from the baery may cause irritaon
or burns.
e) Never service damaged baery packs. Service of
baery packs should only be performed by the
manufacturer or authorized service providers.
6) Service
a) Have your power tool serviced by a qualied repair
person using only idencal replacement parts.
This will ensure that the safety of the power tool is
maintained.
SPECIFIED CONDITIONS OF USE
Safety Instructions Hedge trimmer
Keep all parts of the body in safe distance from the
knife.Do not try to remove the material being cut or
hold material to be cut when the knife is running.
Jammed cuttings to be removed only when the
machine is off and the battery taken out. A moment of
inattention when using the hedge trimmer may result in
serious injuries.
Carry the hedge trimmer by the handle when the
knife is off. Fit the protective cover whenever the
hedge trimmer is to be transported or stored. Careful
treatment with the appliance reduces the risk of injury by
the blade. Hold the power tools by the insulated handles
as the cutting knife may come into contact with hidden
cables/lines. Contact of the cutting knife with a live con-
ductor may bring the metal parts of the appliance under
voltage and cause electric shock.
FURTHER SAFETY INSTRUCTIONS
Before work, check the area for any hidden
items such as wire fences.
When working, keep the appliance firmly with
both hands and with a distance from your
body.
Cordless-Chain saw
• Keep all parts of the body away from the saw chain
when the chain saw is operating. Before you start the
chain saw, make sure the saw chain is not contacting
anything. A moment of inattention while operating
chain saws may cause entanglement of your clothing or
body with the saw chain.
• Always hold the chain saw with your right hand
on the rear handle and your left hand on the front
handle. Holding the chain saw with a reversed hand
configuration increases the risk of personal injury and
should never be done.
• Wear eye protection. Further protective equipment for
hearing, head, hands, legs and feet is recommended.
Adequate protective equipment will reduce personal
injury from flying debris or accidental contact with the
saw chain.
• Do not work on trees with the chainsaw. There is a risk
of injury when working on a tree.
• Always keep proper footing and operate the chain saw
only when standing on fixed, secure and level surface.
Slippery or unstable surfaces may cause a loss of balance
or control of the chain saw.
• When cutting a limb that is under tension, be alert
for spring back. When the tension in the wood fibres is
released the spring loaded limb may strike the operator
and /or throw the chain saw out of control.
• Use extreme caution when cutting brush and sapli-
ngs. The slender material may catch the saw chain and
be whipped toward you or pull you off balance.
• Carry the chain saw by the front handle with the
chain saw switched off and away from your body.
When transporting or storing the chain saw, always
fit the guide bar cover. Proper handling of the chain saw
will reduce the likelihood of accidental contact with the
moving saw chain.
• Follow instructions for lubricating, chain tensioning
and changing the bar and chain. Improperly tensi-
GB
ENGLISH