iLO IWF2706 - Page 17

5-2 L4803EA
2. Initial Setting
General
1. Enter the Service mode. (See page 5-1.)
2. Press [VOL p] button on the service remote
control unit. Display changes “C/D”, “7F”,
“VIDEO”, “AV MEMO”, “STABLE SOUND”, “300”,
“YUV MEMORY”, and “NO SIG BRT” cyclically
when [VOL p] button is pressed.
3. To set the following each data value, press [CH o /
p] buttons on the service remote control unit.
7F---Set to “FF”.
VIDEO---Set to “V1/V2/YUV”.
AV MEMO---Set to “OFF”.
STABLE SOUND---Set to “OFF”.
7E DATA---Set to “300”.
YUV MEMORY---Set to “OFF”.
NO SIG BRT---Set to “0”.
3. Setting for BRIGHT, CONTRAST,
COLOR, S-COLOR, COMPONENT
COLOR, TINT, V-TINT, S-TINT,
COMPONENT TINT, SHARP,
S-SHARP, and COMPONENT
SHARP Data Values
General
1. Enter the Service mode. (See page 5-1.)
2. Press [MENU] button on the service remote
control unit. Display changes “BRT,” “CNT,” “CLR,”
“S-CLR,” “C-CLR,” “TNT,” “V-TNT,” “S-TNT,” “C-
TNT,” “SHARP,” “S-SRP,” and “C-SRP” cyclically
when [MENU] button is pressed.
CNT
1. Press [MENU] button on the service remote
control unit. Then select “CONTRAST” (CNT)
display.
2. Press [CH o / p] buttons on the service remote
control unit so that the value of “CONTRAST”
(CNT) becomes 59.
CLR
1. Press [MENU] button on the service remote
control unit. Then select “COLOR” (CLR) display.
2. Press [CH o / p] buttons on the service remote
control unit so that the value of “COLOR” (CLR)
becomes 73.
S-CLR
1. Press [MENU] button on the service remote
control unit. Then select “S-COLOR” (S-CLR)
display.
2. Press [CH o / p] buttons on the service remote
control unit so that the value of “S-COLOR” (S-
CLR) becomes 73.
C-CLR
1. Press [MENU] button on the service remote
control unit. Then select “COMPONENT COLOR”
(C-CLR) display.
2. Press [CH o / p ] buttons on the service remote
control unit so that the value of “COMPONENT
COLOR” (C-CLR) becomes 59.
TNT
1. Press [MENU] button on the service remote
control unit. Then select “TINT” (TNT) display.
2. Press [CH o / p ] buttons on the service remote
control unit so that the value of “TINT” (TNT)
becomes 54.
V-TNT
1. Press [MENU] button on the service remote
control unit. Then select “V-TINT” (V-TNT) display.
2. Press [CH o / p ] buttons on the service remote
control unit so that the value of “V-TINT” (V-TNT)
becomes 59.
S-TNT
1. Press [MENU] button on the service remote
control unit. Then select “S-TINT” (S-TNT) display.
2. Press [CH o / p ] buttons on the service remote
control unit so that the value of “S-TINT” (S-TNT)
becomes 58.
C-TNT
1. Press [MENU] button on the service remote
control unit. Then select “COMPONENT TINT” (C-
TNT) display.
2. Press [CH o / p ] buttons on the service remote
control unit so that the value of “COMPONENT
TINT” (C-TNT) becomes 63.
SHARP
1. Press [MENU] button on the service remote
control unit. Then select “SHARP” (SHARP)
display.
2. Press [CH o / p ] buttons on the service remote
control unit and select “42.”
S-SRP
1. Press [MENU] button on the service remote
control unit. Then select “S-SHARP” (S-SRP)
display.
2. Press [CH o / p ] buttons on the service remote
control unit and select “40.”
C-SRP
1. Press [MENU] button on the service remote
control unit. Then select “COMPONENT SHARP”
(C-SRP) display.
2. Press [CH o / p ] buttons on the service remote
control unit and select “45.”
Note: BRIGHT data value does not need to be
adjusted at this moment.