Indesit D2I HL326 - User Manual

ENQuick Guide
1
THANK YOU FOR BUYING AN INDESIT PRODUCT.
In order to receive a more complete assistance, please register
your appliance on: www.indesit.com/register
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on
the machine’s functional components.
• It is mandatory that THE SALT RESERVOIR NEVER BE EMPTY.
• It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher
(see PRODUCT DESCRIPTION) and must be lled when the SALT REFILL
indicator light in the control panel is lit.
1. Remove the lower rack and unscrew the reservoir cap
(anticlockwise).
2. Only the rst time you do this: ll the salt reservoir
with water.
3. Position the funnel (see gure) and ll the salt reservoir
right up to its edge (approximately 1 kg); it is not unu-
sual for a little water to leak out.
4. Remove the funnel and wipe any salt residue away from the opening.
Make sure the cap is screwed on tightly, so that no detergent can get into
the container during the wash program (this could damage the water sof-
tener beyond repair).
Whenever you need to add salt, it is mandatory to complete the
procedure before the beginning of the washing cycle to avoid corrosion.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse
aid dispenser A should be lled when when
the dark optical indicator on the dispenser
door C becomes transparent.
NEVER pour the rinse aid directly into the
appliance tub.
D
E
A
C
FILLING THE DETERGENT DISPENSER
To open the detergent dispenser use the opening device D. Introduce the
detergent into the dry dispenser E only. Place the amount of detergent for
pre-washing directly inside the tub.
Usage of detergent not designed for dishwashers may cause malfunc-
tion or damage to the appliance.
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently pre-
venting scale buildup on heater, contributing also to better cleaning eciency.
This system regenerates itself with salt, therefore it is required to rell
salt container when empty.
Frequency of regeneration depends on water hardness level setting - regen-
eration takes place once per 6 Eco cycles with water hardness level set to 3.
Regeneration process starts in nal rinse and nishes in drying phase, be-
fore cycle ends.
• Single regeneration consumes: ~3.5L of water;
• Takes up to 5 additional minutes for the cycle;
• Consumes below 0.005kWh of energy.
CONTROL PANEL
FIRST TIME USE
Before using the appliance carefully read Safety Instructions
guide.
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020.
Note for Test Laboratories:
For information on comparative EN testing conditions, please send an email to the following address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Values given for programmes other than the eco programme are indicative only. The actual time may vary depending on many factors such as temperature
and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and sensor
calibration. The sensor calibration can increase program duration up to 20 min.
PROGRAMS TABLE
1 2 4 53
1. ON-OFF / Reset button with indicator light
2. Program selection button / Push&GO
3. Salt rell indicator light
4. Program indicator lights
5. START/Pause button with indicator light
PLEASE SCAN THE QR CODE ON YOUR
APPLIANCE IN ORDER TO HAVE MORE
DETAILED INFORMATION
Program Programs description
Drying
phase
Duration
of wash
program
(h:min)
*)
Water
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
1.
Eco 50°- Eco program is suitable to clean normally soiled tableware, that
for this use, it is the most ecient program in terms of its combined ener-
gy and water consumption, and that it is used to assess compliance with
the EU Ecodesign legislation.
3:35 9.5 0.95
2.
Intensive 65° - Program recommended for heavily soiled crockery, espe-
cially suitable for pans and saucepans (not to be used for delicate items).
2:40 18.0 1.60
3.
Mixed 55° - Mixed soil. For normally soiled dishes with dried food residues. 2:15 16.0 1.40
4.
Fast&Clean 28’ 50° - Program to be used for half load of lightly-soiled
dishes with no dried food residues. Does not have drying phase.
-
0:28 9.0 0.50
5.
Push&GO 50° - Everyday wash and dry cycle that ensures great cleaning
performance in a short time without the need to pre-treat dishes.
1:30 11.5 1.30
PUSH&GO
Push&GO button (P) is an easily distinguishable button that allows you direct access to the Push&GO program, a wash and dry cycle that ensures great
cleaning performance in a short time. You don’t have to worry which program to choose, Push&GO cycle will do the work for you.
To select Push&GO program, switch on appliance, press only P button for 3 seconds (corresponding indicator lights up) and close the door within 4 seconds.

Summary

Control Panel Overview

ON-OFF; Reset Button

Controls appliance power and resets functions, featuring an indicator light.

Program Selection; Push&GO Button

Used to select wash programs and activate the Push&GO feature.

Salt Refill Indicator Light

Illuminates to signal that the salt reservoir requires refilling.

Program Indicator Lights

Lights that display the currently selected wash program.

START;Pause Button

Initiates, pauses, and resumes the selected wash cycle.

First Time Use Guide

Filling the Salt Reservoir

Instructions for adding salt to prevent limescale buildup on dishes and components.

Filling the Rinse Aid Dispenser

Guidance on refilling the rinse aid dispenser for improved drying.

Filling the Detergent Dispenser

Steps for adding detergent to the dispenser for pre-wash and main wash.

Water Softening System

Explanation of the automatic water hardness reduction system and salt refill requirement.

Programs Table Overview

Loading the Racks

Upper Rack Loading

Instructions for loading delicate and light items such as glasses and cups.

Lower Rack Loading

Guidance for loading pots, plates, and larger items.

Foldable Flaps

Information on the adjustable position of foldable flaps.

Cutlery Basket

Details on cutlery basket placement and arrangement for improved cleaning.

Cleaning and Maintenance

Cleaning the Filter Assembly

Steps for cleaning the filter assembly to ensure optimal performance.

Cleaning the Spray Arms

Instructions on how to remove and clean the spray arms.

Troubleshooting Common Issues

Indesit D2I HL326 Specifications

General

Door color	Not applicable
Water fill	Cold, Hot
Cord length	1.3 m
Control type	Buttons
Product size	Full size (60 cm)
Built-in display	No
Inlet hose length	1.55 m
Custom panel-ready	-
Outlet hose length	1.5 m
Appliance placement	Fully built-in
Control panel color	White
Baskets adjustable placement	Upper
Current	10 A
Connected load	1900 W
AC input voltage	220-240 V
AC input frequency	50 Hz
Energy efficiency scale	A to G
Water consumption per cycle	9.5 L
Package weight	37500 g
Cycle time	215 min
Noise level	46 dB
Overflow protection	Yes
Dishwashing programs	Daily 50°C, Eco 50°C, Intensive 65°C, Mixed, Quick 29min
Number of place settings	14 place settings
Number of washing programs	5

Weight and Dimensions

Depth	555 mm
Width	598 mm
Height	820 mm
Weight	35500 g
Installation compartment depth	560 mm
Installation compartment width	600 mm
Installation compartment height (max)	900 mm