Why Infiniton SD-3M Dryer clothes too dry?
Clothes may be too dry due to several reasons. There might be too much laundry in the dryer. Also, laundry is not taken out in time when finished, or laundry is not sorted correctly. Finally, the temperature may be too high. To resolve this, ensure there is no overload of laundry, take the laundry out immediately when finished, and respect the maintenance label on the laundry.
What to do if my Infiniton Dryer smells burnt?
If your dryer smells burnt, the lint filter or the suction/exhaust duct might be dirty. Make sure to clean the lint filter well in advance, and clean the tube.
How to fix Infiniton SD-3M Dryer that does not start?
If your dryer doesn't start, the issue might be due to a power failure, a disconnected plug, the laundry temperature being too high, or a disconnected temperature fuse. Wait until the power is restored. Check the socket to ensure the plug is properly connected. The laundry in the dryer must be after spinning, and the laundry to be dried must not exceed 3 kg. If the temperature fuse is disconnected, call a service technician to reset it.
Why does lint form on clothes in Infiniton SD-3M Dryer?
Lint forms on clothes because synthetic fibres and permanent press fibre cause hairballs. This is because the rubbing causes the formation of fluff. To reduce lint, use fabric softener to lubricate the fibre. When ironing clothes, apply a little fabric softener to the cuffs and neckline, and turn the iron outwards to reduce rubbing.
What to do if clothes shrink in Infiniton SD-3M?
If clothes shrink in the dryer, it might be too dry. Observe the care label on the laundry. If clothes shrink easily, examine them when they are dry. Remove clothes when they are too wet or too dry and hang them up until they are completely dry.
Why is my Infiniton Dryer external hot or smells hot?
If your Infiniton Dryer is externally hot or smells hot, the lint filter or the uptake/exhaust duct may be dirty. Make sure to clean the lint filter promptly and clear out any obstructions in the stem.
What to do if my Infiniton SD-3M Dryer will not start?
If your Infiniton Dryer doesn't start, several factors could be the cause. First, check for a power cut or if the power plug isn't securely plugged in. Wait for the electricity to be restored and ensure the plug is tight in the socket. Also, make sure you are not drying more than 3kg of clothes and that the clothes have been spun before drying. If the temperature fuse is cut, have a professional repair it.
Why are my clothes too dry after using Infiniton SD-3M Dryer?
If your clothes are too dry after using the Infiniton Dryer, it could be due to overloading the machine, not removing the clothes promptly after the cycle, improper sorting, or setting the temperature too high. Ensure the dryer isn't overloaded, take out the clothes immediately after drying, observe the maintenance label on clothes.
Why does my Infiniton Dryer cause hairballs on clothes?
Hairballs on clothes after using your Infiniton Dryer are typically caused by synthetic and permanent press fibers rubbing together. To reduce this, use fabric softener to lubricate the fibers. You can also spray a settled glue on cuffs and necklines when ironing. Turn clothes inside out to reduce rubbing.
How to prevent clothes from shrinking in my Infiniton Dryer?
To prevent clothes from shrinking in your Infiniton Dryer, pay attention to the maintenance label on clothes. If the clothes are prone to shrinking, check them while drying. Take them out when slightly damp if they are getting too dry and hang them until fully dry.
General| Appliance placement | Freestanding |
|---|---|
| Rated capacity | 8 kg |
| Anti-Crease function | Yes |
| Energy efficiency class | A++ |
| Heat source | Electric |
| Product colour | White |
| Loading type | Front load |
| Drying programs | Cotton, Quick, Delicate |
To Next Page
