Infinity 5761A - User Manual

Other manuals for Infinity 5761A

Service Manual33 pages

Instruction Manual12 pages

Questions and Answers

K
Kara HurleyAug 20, 2025
How to troubleshoot Infinity Amplifier with no audio and POWER LED is off?
- M
  Molly DoyleAug 20, 2025
  If your Infinity Amplifier has no audio and the POWER LED is off, check the voltages at the amplifier terminals with a VOM.
R
Rachel BarnesAug 22, 2025
How to fix distorted audio on my Infinity Amplifier?
- B
  Beth WilliamsAug 22, 2025
  If you are experiencing distorted audio with your Infinity Amplifier, it could be due to the input sensitivity not being set correctly, or there may be a defect in the amplifier or source unit. First, check the INPUT LEVEL setting. Also, inspect the speaker wires for any shorts or grounds.
W
wadkinsAug 25, 2025
What to do if there is no audio and the PROTECT LED is on in my Infinity 5761A Amplifier?
- G
  gsmithAug 25, 2025
  If there is no audio and the PROTECT LED is on for your Infinity Amplifier, it's likely that the amplifier is overheated. Ensure that the amplifier cooling is not blocked at the mounting location. Also, verify that the speaker-system impedance is within the specified limits.
R
robbinsmeganAug 26, 2025
What to do if my Infinity 5761A has distorted audio and the PROTECT LED flashes?
- D
  David HansonAug 27, 2025
  If you're getting distorted audio and the PROTECT LED is flashing on your Infinity Amplifier, there may be a short circuit in the speaker or wire. Remove the speaker leads one at a time to find the shorted speaker or wire, and then repair it.
J
Justin FrancisAug 28, 2025
How to troubleshoot no audio when the POWER LED is off on my Infinity Amplifier?
- B
  Brian AvilaAug 28, 2025
  If there is no audio and the POWER LED is off on your Infinity Amplifier, it indicates that there is no voltage at the BATT+ and/or REM terminals, or there's a bad or no ground connection. Check the voltages at the amplifier terminals using a VOM (volt-ohm-milliammeter).
J
jonesshaneAug 30, 2025
What does it mean when the PROTECT and POWER LEDs flash on my Infinity 5761A with no audio?
- C
  Cristian Anderson DVMAug 30, 2025
  If there is no audio and both the PROTECT and POWER LEDs are flashing on your Infinity Amplifier, it means the voltage is less than 9V on the BATT+ connection. Check the vehicle charging system.
M
Maureen LevineSep 1, 2025
Why is there no audio and the PROTECT LED is on for my Infinity Amplifier?
- J
  jimmysullivanSep 1, 2025
  If there is no audio and the PROTECT LED is on for your Infinity Amplifier, it means the voltage is greater than 16V or less than 8.5V on the BATT+ connection. Check the vehicle charging system.
R
Ricardo FigueroaSep 3, 2025
What to do if there is no audio and the PROTECT LED flashes on my Infinity Amplifier?
- C
  cwilsonSep 3, 2025
  If there is no audio and the PROTECT LED flashes on your Infinity Amplifier, it indicates there is DC voltage on the amplifier output. The amplifier may need service; see enclosed warranty card for service information.
M
Mark RamseySep 5, 2025
What to do if my Infinity 5761A Amplifier has distorted audio?
- S
  Stephanie BrownSep 5, 2025
  If you're experiencing distorted audio with your Infinity Amplifier, it could be due to an improperly set input sensitivity or a defect in the amplifier or source unit. First, check the INPUT LEVEL setting. Also, inspect the speaker wires for any shorts or grounds.
K
kellyandrewSep 7, 2025
Why does my Infinity Amplifier lack punch?
- W
  Willie MaxwellSep 7, 2025
  If your music lacks 'punch' when using the Infinity Amplifier, the speakers might not be connected properly. Check the speaker connections to ensure they have the correct polarity.