Ingersoll-Rand 1R Series User Manual

Ingersoll-Rand 1R Series

12 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

16575243

Edition 2

October 2013

Save These Instructions

Air Screwdrivers

1R Series

Maintenance Information

Questions and Answers:

T
Timothy NicholsAug 12, 2025
Why Ingersoll-Rand 1R Power Screwdriver loses power?
- E
  Erin GoodwinAug 12, 2025
  Loss of power in your Ingersoll-Rand Power Screwdriver can stem from several causes. It might be due to low air pressure; ensure the air supply is at 90 psig (6.2 bar/620 kPa) at the inlet for optimal performance. A plugged air strainer or inlet screen could also be the culprit; clean or replace these components. Similarly, a clogged muffler or exhaust silencer needs cleaning or replacement. Worn or broken vanes require replacement of the entire set. A damaged rear end plate gasket necessitates a new gasket. Inspect the cylinder for wear or breakage, replacing it if cracked or scored. Finally, improper lubrication or dirt build-up calls for cleaning and lubrication of the motor unit parts.
M
Michelle ThomasAug 19, 2025
What to do if Ingersoll-Rand 1R motor stalls before adjustable clutch ratchets?
- C
  Christopher SheaAug 19, 2025
  If the motor stalls before the adjustable clutch ratchets on your Ingersoll-Rand Power Screwdriver, the issue could be due to improper clutch adjustment or an unsuitable tool ratio for the application; check the clutch adjustment and review the tool's performance against the requirements. Low air pressure at the inlet can also cause this; ensure the air supply is at 90 psig (6.2 psig/620 kPa). Insufficient grease is another potential cause; lubricate the clutch as instructed.
D
Dennis WangAug 27, 2025
How to fix a leaky throttle valve on Ingersoll-Rand 1R Power Screwdriver?
- J
  Julie JohnsonAug 27, 2025
  A leaky throttle valve in your Ingersoll-Rand Power Screwdriver can be fixed by addressing the potential causes. If the throttle valve and/or throttle valve seat are worn, install new ones. Alternatively, dirt accumulation on these parts can be resolved by pouring about 3 cc of a clean cleaning solution into the air inlet and operating the tool valve for about 30 seconds, then immediately lubricating the cleaned parts with 3 cc of the recommended oil.
H
Hannah SanchezSep 4, 2025
Why is the adjustable clutch on my Ingersoll-Rand 1R disengaging inconsistently?
- J
  James ThompsonSep 4, 2025
  Inconsistent disengagement of the adjustable clutch on your Ingersoll-Rand Power Screwdriver could be caused by improper lubrication. Remove the adjustable clutch mechanism, examine the parts, and lubricate as instructed. Another cause might be using the wrong clutch spring, such as a heavy clutch spring on a light torque application; change to a medium or light clutch spring.

Ingersoll-Rand 1R Series Specifications

General

Brand	Ingersoll-Rand
Model	1R Series
Category	Power Screwdriver
Language	English

Related product manuals

Ingersoll-Rand 1RPNS1-IR

Preview: Ingersoll-Rand QX Series

Ingersoll-Rand QX Series

Ingersoll-Rand 5L Series

Preview: Ingersoll-Rand 41 Series

Ingersoll-Rand 41 Series

Preview: Ingersoll-Rand 5 series

Ingersoll-Rand 5 series

Ingersoll-Rand 5RALC1

Ingersoll-Rand 5RANC1

Ingersoll-Rand 5RLNC1

Preview: Ingersoll-Rand D5000 Series

Ingersoll-Rand D5000 Series

Preview: Ingersoll-Rand 5LL2D6

Ingersoll-Rand 5LL2D6