Ingersoll-Rand M951P060BU36AA User Manual

© 2012 Ingersoll Rand All Rights Reserved
Upflow/ Horizontal, Downflow/ Horizontal, Gas-Fired, Direct Vent
Condensing Furnaces
INSTALLER'S GUIDE
M95 Upflow models can also be used in the
Horizontal Left configuration.
M95 Downflow models can also be used in the
Horizontal Right configuration.
A341624P16
M95 Furnace
18-CD35D1-4
OPTIONAL ACCESSORIES
Model Number Description
BAYBASE205 Downflow subbase for downflow models only
BAYFLTR200 External side filter rack
BAYFLTR203 Filter kit horizontal for 17.5" cabinet
BAYFLTR204 Filter kit horizontal for 21" cabinet
BAYFLTR205 Filter kit horizontal for 24.5" cabinet
BAYFLTR317 Cleanable filter for 17.5" cabinet upflow only
BAYFLTR321 Cleanable filter for 21" cabinet upflow only
BAYFLTR324 Cleanable filter for 24.5" cabinet upflow only
BAYLPKT210B Propane conversion kit
BAYLPSS210B LP kit with stainless steel burners
BAYMFGH100A Manufactured / mobile home kit
BAYRACK960A Internals filter rack kit for upflow models
BAYAIR30AVENTA Concentric vent kit for 2,2.5,3" vent system
BAYVENT200B Sidewall vent termination kit for direct vent furnaces
BAYVENT500A Side vent kit for downflow models only
BAYSWT01AHALTA High altitude switch kit - UF/DF 040, DF 085
BAYSWT04AHALTA High altitude switch kit - UF 060, 100, UF 120
BAYSWT05AHALTA High altitude switch kit - UF 080, 100, DF 110
BAYSWT12AHALTA High altitude switch kit - DF 065
KIT09224 Filter clip kit
BAYBRCKFLT10 Downflow bracket kit
ALL phases of this installation must comply with
NATIONAL, STATE AND LOCAL CODES
IMPORTANT — This Document is customer property and is to
remain with this unit. Please return to service
information pack upon completion of work.
M951P040BU24AA
M951P060BU36AA
M951P080BU42AB
M951P100CU48AA
M951P100DU60AA
M951P120DU60AA
M951P040BD24AA
M951P065BD42AA
M951P085CD48AA
M951P110DD60AA

Ingersoll-Rand M951P060BU36AA Specifications

General

Brand	Ingersoll-Rand
Model	M951P060BU36AA
Category	Furnace
Language	English

Summary

Installation Instructions

Safety Section

Details essential safety practices and precautions for furnace installation, servicing, and operation.

Carbon Monoxide Poisoning Hazard

Warns of fatal risks from improper appliance venting and outlines critical steps for safe operation.

General Installation Guidelines

Location and Clearances

Air for Combustion and Ventilation

General Venting

Installation of Carbon Monoxide Detectors

Requirements for installing carbon monoxide detectors in conjunction with the furnace installation.

Combustion and Input Check

High Altitude Derate

Start Up and Adjustment

Preliminary Inspections

Pre-operation checks and verifications to ensure safe and correct installation.

Lighting Instructions

Sequence of Operation

Control and Safety Switch Adjustments

Procedures for adjusting and verifying the function of safety controls and switches.

Limit Switch Check Out

Procedure to test the furnace's limit switch functionality for overheating protection.

Airflow Adjustment

Abnormal Conditions

Burner Box Temperature Limit Device

Describes the function and location of the burner box temperature limit switch.

Excessive Combustion Pressure (Wind in Excess of 40 M.P.H.) Vent or Flue Blockage

Explains how vent blockage or high wind affects combustion pressure and unit operation.

Loss of Flame

Describes furnace behavior and lockout procedures when flame is lost.

Gas Supply Failure

Describes furnace behavior and lockout procedures during a gas supply interruption.

Induced Draft Blower Failure

Explains how failure of the draft blower affects furnace operation and safety.

Condensate Drain Blockage

Details how a blocked condensate drain impacts furnace operation and safety.

Reset After Lockout

Reset After Burner Box Limit Shutdown

IFC Error Flash Code

Explains the meaning of various flash codes generated by the Integrated Furnace Control.

Condensate Drain Instructions

Vertical Applications

Specific instructions for condensate drain setup in vertical furnace installations.

Horizontal Applications