EasyManua.ls Logo

Ingersoll-Rand PB35A - User Manual

Ingersoll-Rand PB35A
8 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
51990497
Edition 4
May 2014
Save These Instructions
Paving Breaker
Models PB35A, PB35AS, PB50A and PB50AS
(With/Without Flex Handles)
Maintenance Information

Table of Contents

Questions and Answers

  • G
    Geoffrey HendersonAug 12, 2025
    Why does my Ingersoll-Rand Power Tool paving breaker lack power?
    • J
      Julie CrawfordAug 12, 2025
      If your Ingersoll-Rand Power Tool paving breaker lacks power, ensure the air supply pressure at the tool is between 90 to 100 psi (6.2 to 6.9 bar). Keep the shank fed-up to the work, maintaining constant pressure. Also, dismantle the breaker and clean out all ports and passages. Maintain the proper oil level in the lubricating oil reservoir, ensuring the steel shank shows a film of oil. If the valve is sticking, remove valve chest parts from the breaker and clean them, avoiding dirty or non-specification oil.
  • N
    nicole29Aug 16, 2025
    How to fix Ingersoll-Rand Power Tool paving breaker that will not start?
    • X
      xcastilloAug 16, 2025
      If your Ingersoll-Rand Power Tool paving breaker will not start, the exhaust port or air passages might be plugged due to dirt or hose particles. Dismantle the breaker and clean all ports and air passages, ensuring the air hose is in good condition. A stuck valve, caused by gummy oil or incorrect assembly, can also prevent starting. Remove and clean the valve chest parts, and only use oil that conforms to the recommended specifications. Another cause can be a frozen piston due to improper lubrication. Dismantle the breaker to remove the Piston and repair it by placing it in a high-speed lathe and dressing it with fine emery cloth. Always ensure the lubricating oil reservoir has the proper lubricating oil.
  • G
    Gloria WardAug 20, 2025
    What to do if Ingersoll-Rand Power Tool paving breaker overheats after break-in?
    • A
      Alyssa PerryAug 20, 2025
      If your Ingersoll-Rand Power Tool paving breaker is overheating after the break-in period, keep the shank fed-up to the work and maintain constant pressure. If the piston isn't hitting the shank because of a short shank, remove the shank piece from the breaker. When pulling steels, always use minimum throttle. Before operating the breaker, ensure the lubricating oil reservoir is full of proper lubricant; a lack of lubrication or improper lubricating oil can cause overheating.
  • N
    Natasha FisherAug 23, 2025
    Why Ingersoll-Rand Power Tool paving breaker loses power rapidly?
    • M
      Michelle GarciaAug 25, 2025
      If your Ingersoll-Rand Power Tool paving breaker loses power rapidly, check for restrictions in the air supply line, ensuring it doesn't kink or make sharp bends. Also, keep the air supply line under 50 ft (15 m). A 3/4 in. (19.1 mm) diameter air supply line is recommended for the breaker.
  • E
    Emily KirbyAug 27, 2025
    How to troubleshoot erratic operation of Ingersoll-Rand Power Tool?
    • A
      andersonaaronAug 28, 2025
      If your Ingersoll-Rand Power Tool is experiencing erratic or sluggish operation, use only the recommended lubricating oil, as heavy oil can slow down valve action. Also, dismantle the breaker and clean out dirt and gummy residue, then service the breaker with clean oil. Protect the tool from dirt when idle.
  • J
    Jennifer JacksonAug 31, 2025
    What causes overheating of the piston seat on a new Ingersoll-Rand Power Tool?
    • A
      amy13Aug 31, 2025
      If the piston seat on your new Ingersoll-Rand Power Tool machine is overheating, stop operating the breaker and perform initial servicing. Never run a new breaker at full throttle until a proper break-in period has been completed.
  • L
    Laura CervantesSep 3, 2025
    How to prevent freezing at exhaust ports of Ingersoll-Rand Power Tool?
    • H
      harperjacobSep 3, 2025
      If you notice freezing at the exhaust ports of your Ingersoll-Rand Power Tool, install moisture traps in the air supply line or add anti-freeze lubricant directly through the air inlet. Use “KILFROST” anti-freeze lubricant or equivalent.
  • U
    ugonzalezSep 7, 2025
    What to do if Ingersoll-Rand Power Tool is fogging?
    • L
      Lisa LewisSep 7, 2025
      If your Ingersoll-Rand Power Tool is fogging, blow out the air lines. If moisture traps are installed in the air supply line, drain the moisture. Also, clean the lubricating oil reservoir and adjust for the proper rate of feed, as over lubrication can cause fogging.

Ingersoll-Rand PB35A Specifications

General IconGeneral
BrandIngersoll-Rand
ModelPB35A
CategoryIndustrial Equipment
LanguageEnglish

Related product manuals