Ingersoll-Rand SSR UP6-10 User Manual

48 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

C.C.N. : 80445273

REV. : A

DATE : OCTOBER 2008

SSR UP5-4, UP5-5.5, UP5-7.5, UP5-11c

50 Hz

SSR UP6-5, UP6-7.5, UP6-10, UP6-15c

60 Hz

OPERATION AND MAINTENANCE MANUAL

This manual contains

important safety information

and must be made available

to personnel who operate

and maintain this machine.

Refer all communications to the nearest Ingersoll Rand Full Service Distributor.

Table of Contents

Questions and Answers:

H
heathmeganAug 8, 2025
What to do if the drain timer is not working on my Ingersoll-Rand Air Compressor?
- J
  Jennifer GriffinAug 8, 2025
  If the drain timer on your Ingersoll-Rand Air Compressor isn't working, here's what might be happening and how to address it: 1. **No electrical supply:** Ensure the unit is receiving power. 2. **Timer malfunction:** The timer itself may be faulty and need replacement. 3. **Clogged port:** A blocked port can prevent operation; try cleaning the valve. 4. **Solenoid valve malfunction:** The solenoid valve could be defective, requiring replacement. 5. **Clogged strainer:** A blocked strainer may be the issue; clean the strainer.
S
Sean BakerAug 16, 2025
Why won't the solenoid condensate valve close on my Ingersoll-Rand SSR UP6-10?
- S
  Samantha PhillipsAug 17, 2025
  If the solenoid condensate valve on your Ingersoll-Rand Air Compressor won't close, it could be due to a couple of reasons. First, debris might be preventing the diaphragm from seating properly; in this case, you should remove the solenoid valve, disassemble it, clean all the parts, and then reassemble it. Alternatively, there could be a short in an electrical component. Check the power cord or timer and replace them if necessary.
E
Erin James DDSAug 23, 2025
Why timer will not activate on my Ingersoll-Rand Air Compressor?
- B
  Brian RamosAug 25, 2025
  If the timer on your Ingersoll-Rand Air Compressor won't activate, there are several potential causes. First, ensure that the unit is receiving electrical power by verifying the power supply. If power is present, the timer itself may be malfunctioning and require replacement. Additionally, a clogged port or strainer could be preventing activation; try cleaning the valve and strainer. Finally, a malfunctioning solenoid valve could be the culprit, in which case it should be replaced.
B
Beth YoungAug 31, 2025
What to do if valve will not close on my Ingersoll-Rand SSR UP6-10 Air Compressor?
- M
  monicawalterSep 1, 2025
  If the valve on your Ingersoll-Rand Air Compressor won't close, it could be due to debris in the solenoid valve preventing the diaphragm from seating properly. To resolve this, remove the solenoid valve, disassemble it, thoroughly clean all components, and then reassemble it. Alternatively, a short in an electrical component, such as the power cord or timer, could be the cause. Inspect these components and replace them as necessary.

Ingersoll-Rand SSR UP6-10 Specifications

General

Model	SSR UP6-10
Type	Rotary Screw
Horsepower	10 HP
Max Pressure	125 PSI
Voltage	208-230/460 V
Weight	650 lbs
Phase	3 Phase
Tank Size	80 gal

Summary

Warranty Information

Safety Precautions

DANGER

Identifies hazards causing death or severe injury if ignored.

WARNING

Identifies hazards that can cause death or severe injury.

CAUTION

Identifies hazards that could damage product or surroundings.

Breathing Air Precaution

Warning against using compressed air for breathing without treatment.

Installation and Handling

Electrical Data: UP6 7.5

Electrical Data: UP6 10

Electrical Data: UP6 15c

Electrical Data: UP5 4

Electrical Data: UP5 5.5

Electrical Data: UP5 7.5

Electrical Data: UP5 11c

Operating Instructions

General Operation Overview

Compressor Controls

Description of the compressor's control panel and components.

Automatic Start & Stop Control

Explanation of automatic start/stop functionality.

Dual Control Modes

Prior to Starting Checks

Pre-operation checks and safety precautions before startup.

Starting Procedure

Normal and Emergency Stopping

How to stop the compressor during normal or emergency situations.

Maintenance Procedures

Maintenance Schedule

Periodic maintenance tasks and intervals for UP Series.

Routine Maintenance Guidelines

General guidance for regular maintenance procedures.

Coolant Change Procedure

Coolant Filter Change Procedure

Air Filter Element Change Procedure

Separator Element Change Procedure

Troubleshooting Common Issues

Compressor Fails to Start

Common causes and remedies for compressor startup failure.

Machine Shuts Down Periodically

Reasons for periodic shutdowns and solutions.

High Current Draw Issues

Causes and remedies for excessive current draw.

Low Current Draw Issues

Causes and remedies for low current draw.

High Discharge Pressure

Causes and remedies for high discharge pressure.

Low System Air Pressure

Causes and remedies for low system air pressure.

High Dewpoint in Compressed Air

Causes and remedies for high dewpoint in compressed air.

Ice Formation in Dryer

Compressor Trips Due to Over Temperature

Reasons for compressor tripping due to overheating and solutions.

Excessive Coolant Consumption

Causes and remedies for high coolant usage.

Excessive Noise Level

Causes and remedies for excessive noise from the unit.

Shaft Seal Leaking

Pressure Relief Valve Opens

Reasons for pressure relief valve activation and troubleshooting.

Safety Valve Blows During Load

Troubleshooting safety valve activation during operation.

Related product manuals

Preview: Ingersoll-Rand SSR UP6 15

Ingersoll-Rand SSR UP6 15

Ingersoll-Rand SSR UP6-15c

Ingersoll-Rand SSR UP6-5

Ingersoll-Rand SSR UP6 40

Ingersoll-Rand SSR UP6 25

Ingersoll-Rand SSR UP6-7.5

Ingersoll-Rand SSR UP6 50PEI

Preview: Ingersoll-Rand SSR UP5-4

Ingersoll-Rand SSR UP5-4

Ingersoll-Rand SSR UP5-11c

Preview: Ingersoll-Rand SSR M4

Ingersoll-Rand SSR M4

Intellisys SSR 10-40

Preview: INTELLISYS SSR Series

INTELLISYS SSR Series