Need help?Do you have a question about the Ingersoll 4018 and is the answer not in the manual?
Safety instruction on disengaging power to attachments when transporting or not in use.
Safety precautions for handling flammable gasoline, including container use and storage.
Safety warning about high-pressure hydraulic systems and protection against leaks.
Warning about dangerous hillside operation and advising to read the relevant section.
Instructions for jumpstarting the tractor, emphasizing cable connections and safety.
Guidance on learning tractor controls, practice, and understanding operating characteristics.
Advice on inspecting terrain, identifying obstacles, and marking them for safe operation.
Instruction to operate at a slow speed for control, using low gear and regulating throttle.
Emphasizes operator judgment for slope negotiation and advises to stay off if in doubt.
Notice regarding spark arresters and state regulations for machinery use.
Information on Canadian regulations requiring resistor spark plugs for tractors.
Explanation of directional terms used in the manual relative to the operator's position.
Provides space for users to record key identification numbers for their tractor.
Identifies and describes the tractor's main operating controls and instruments.
Instructions on how to use the ignition key to start, run, and stop the engine.
Instructions for engaging and disengaging the PTO switch and its indicator light.
Instructions for selecting low, neutral, and high ranges on the dual range transaxle.
Pre-operation checks covering fuel, oil, controls, and safety features.
Safety warnings related to handling flammable gasoline before operation.
Guidance on controlled break-in for internal engine parts for satisfactory service.
Step-by-step procedure for starting the tractor engine, including choke and throttle settings.
Procedure for warming the hydraulic system in cold temperatures before operation.
Critical warning against attempting to start the tractor by pushing or towing.
Step-by-step procedure for stopping the tractor, including engaging the parking brake and removing the key.
Safety steps for leaving the vehicle unattended.
Initial operation advice: use flat areas, learn characteristics before first job.
Instruction to select the appropriate gear range based on the task.
Step-by-step guide for engaging and controlling forward and reverse travel.
Lists common causes and solutions for the engine failing to start.
Lists common causes and solutions for the engine lacking power.
Lists common causes and solutions for the engine stopping or not running.
Introduction to preventive maintenance for keeping the tractor in top operating condition.
Recommendation to consult the engine manual for engine-specific maintenance.
Lists maintenance procedures, corresponding pages, and recommended frequencies.
Lists the capacities for hydraulic system, transaxle, fuel tank, and engine crankcase.
Technical specifications for the Briggs & Stratton Vanguard engine models used.
Specifications for the tractor's transaxle type, differential, and speed ranges.
Specifications for tire type, size, ply, and recommended pressure.
Provides key overall dimensions of the tractor, such as length, width, and height.
Shows the electrical wiring diagram for the 4200 series with PTO harness.
Lists the wire color codes used in the wiring diagrams.
Shows the electrical wiring diagram for the 4000 series with PTO harness.
Lists the wire color codes used in the wiring diagrams.
Instructions for cleaning and maintaining battery terminals and posts.
Advice on maintaining battery voltage when the tractor is idle.
Safety advice for using jumper cables, including protective gear.
Step-by-step instructions for connecting jumper cables to start the tractor.
Step-by-step instructions for replacing a headlight bulb.
Procedure for replacing the 30 amp fuse that protects most circuits.
Procedure to burnish the clutch lining for normal wear life.
Instructions for lubricating the brake linkage pivot points.
How to adjust the brake for proper stopping and lever return.
Safety warnings for handling and storing flammable gasoline.
Important warning about using gasoline containing alcohol.
Recommendation for changing hydraulic oil seasonally or every 500 hours.
Specifies the correct hydraulic oil level range.
Step-by-step procedure for draining the hydraulic oil.
Instruction to keep the hydraulic oil cooler clean and unobstructed.
Recommendation for replacing the hydraulic oil filter.
Step-by-step instructions for replacing the hydraulic oil filter.
Procedure for adjusting the seat position if no adjustment lever is present.
Cleaning and care instructions for the seat, including protection from weather.
Recommendation for changing transaxle oil every 500 hours.
Location of the transaxle oil fill, drain, and check plugs.
Lists lubrication points for chassis components, requiring grease every 25 hours.
Specifies the type of grease to use and how to apply it.
Safety caution for steering adjustment, ensuring proper free play.
Importance of checking ball joints, drag link, or tie rod before steering adjustment.
Steps for adjusting front wheel toe-in, including measurements and tie rod adjustments.
Information on obtaining parts, operator, and service manuals.
Instructions on how to order manuals, including contact information.
To Next Page
General