What does 'Meter COM Err' mean on my INHENERGY Inverter?
If your INHENERGY Inverter displays 'Meter COM Err', check whether the meter matches the inverter protocol and ensure the wire connection between the meter and inverter is secure.
What does 'Battery Open' mean on my INHENERGY HI-3K-SL Inverter?
If your INHENERGY Inverter shows a 'Battery Open' error, verify that the battery connection is properly secured. Also, check that all switches between the battery and the inverter are turned on.
What to do if my INHENERGY HI-3K-SL Inverter shows 'EPS Volt Low'?
If your INHENERGY Inverter displays 'EPS Volt Low', check the load on the Back-Up. If an overload has occurred, reduce the load. You can also try restarting the inverter.
What does 'PV Volt High' mean on INHENERGY HI-3K-SL Inverter?
If your INHENERGY Inverter displays 'PV Volt High', verify that the voltage of the PV input is within the specified range.
What to do if INHENERGY HI-3K-SL Inverter shows 'BatVolt High'?
If your INHENERGY Inverter displays 'BatVolt High', check to ensure the battery voltage is within the specified range. Also, verify the battery connection is correct. If the voltage is indeed higher than 60V, disconnect the battery and inspect the inverter.
What does 'N-PE Fault!' mean on INHENERGY Inverter?
If your INHENERGY Inverter displays 'N-PE Fault!', check whether the L line and N line are reversed. Also, check whether the PE is properly connected.
What does 'BAT NTC Open' mean on INHENERGY Inverter?
If your INHENERGY Inverter displays 'BAT NTC Open', check whether the temperature sensor of the lead-acid battery is installed. Also, check that the temperature sensor of the lead-acid battery is properly connected.
What to do if my INHENERGY HI-3K-SL says 'Bat Need Chg'?
If your INHENERGY Inverter displays 'Bat Need Chg', you can resolve it by: 1. Setting the battery stop discharge SOC to a higher value. 2. Charging the battery properly.
How to troubleshoot 'Bat Volt Low' error on INHENERGY HI-3K-SL Inverter?
If you see 'Bat Volt Low' on your INHENERGY Inverter, check the battery's actual voltage and ensure the wiring between the battery and inverter is in good condition.
What does 'Battery Open' mean on my INHENERGY HI-3K-SL Inverter and how to fix it?
If your INHENERGY Inverter shows 'Battery Open', verify that: * The battery connection is secure. * All switches between the battery and the inverter are turned on.
General| Max. DC Input Voltage | 550 V |
|---|---|
| Nominal AC Output Power | 3000 W |
| Max. AC Output Power | 3300 W |
| Nominal AC Voltage | 230 V |
| Max. Output Current | 15 A |
| Efficiency | 97.5% |
| Protection Degree | IP65 |
| Output Power | 3000 W |
| Peak Power | 3300 W |
| Output Voltage | 230 V |
| Frequency | 50/60 Hz |
| Cooling | Natural Convection |
| Max. DC Input Power | 4500 W |
| MPPT Voltage Range | 125-500 V |
| Input Voltage | 125V-500V |
| Protection Features | Overvoltage, Short Circuit |
| Operating Temperature | -25°C to 60°C |
Details the function and features of the hybrid inverter series.
Specifies the inverter models covered and the target audience for the manual.
Explains safety symbols used in the manual to prevent injury or damage.
Instructions for checking the inverter for damage incurred during transportation.
Details the items included in the inverter package for verification.
Provides conditions and precautions for installing the inverter outdoors.
Specifies the minimum clearance dimensions required around the inverter for installation.
Step-by-step guide for physically mounting the inverter onto a wall bracket.
Details how to connect photovoltaic (PV) panels to the inverter's DC inputs.
Explains the procedure for connecting batteries to the inverter, including cable requirements.
Covers the connection procedures for grid, generator, and backup power sources.
Describes how to properly ground the inverter for safety.
Details the connection of communication ports for monitoring and data exchange.
Explains the connection and function of the CT1 port for current sensing.
Details the optional connection of a meter for grid voltage and current monitoring.
Describes how to connect the Battery Management System (BMS) for battery communication.
Covers the connection of the DRED device for Australian and New Zealand installations.
Covers fundamental safety guidelines for product installation and operation.
Provides safety guidelines specific to operating inverters in a parallel system.
Details parallel connection for single-phase systems with parallel batteries and up to 3 inverters.
Details parallel connection for single-phase systems with independent batteries and up to 3 inverters.
Explains the parameter settings required for successful parallel operation.
Details parallel connection for three-phase systems with parallel batteries and up to 3 inverters.
Details parallel connection for three-phase systems with independent batteries and up to 3 inverters.
Explains the parameter settings required for successful three-phase parallel operation.
Accessing the inverter's setting menus and options.
Guides on checking and setting the system's current date and time.
Describes how to select and verify the appropriate grid connection standard.
Explains how to select and configure the connected battery type and its parameters.
Details how to set the CT1 type for accurate power measurement in self-consumption mode.
Guides on setting the optional CT2 type for monitoring on-grid inverter power.
Explains how to configure parameters for the inverter's backup power function.
Configuration and operation of the inverter for peak load shifting functionality.
Details operation and settings for optimizing self-consumption of generated solar power.
To Next Page
