FAQ
1.Why the probes display inaccurate temperature? Such as 572F or
display ‘------‘?
Answer: First please check the probes whether firmly inserted in the unit
and make sure no gaps. Customers really need push it hard in. Then
change probes to insert in different ports to check if the probe itself has
problem. Please make sure your probes firmly inserted, otherwise will
display’-----‘ even if the cell phone pair with Bluetooth successfully.
2.Can I put this unit in high temperature places?
Answer: No, it can’t. The plastic back magnet temperature should not over
80℃/176F. Otherwise the unit will melt. Probe temperature range: 32° F ~
572 ° F; (Short-time measurement); 32° F~ 482 ° F (continuousmonitor-
ing).
3.Why cell phone can not search the app?
Answer: Please make sure your GPS is on(Android phone).
4.Why I need a 4 number pin code? What’s correct steps to pair with
cell phone?
Answer: This unit no need for pin code. Here are two solutions:
First, for some customers who have used our Inkbird other thermometers
before, you have to delete the before record, then to pair with this product.
Because one cell phone can only connect one unit at one time. Second,
The correct procedure is activate your Bluetooth on your phone first, open
the BBQGO APP to press the bottom start button to search, then press the
on button of your unite for about 4 seconds it should connect.
5.Can this unit be submerged into water?
Answer: No, customers can use at outdoor when raining. The unused
sockets should be inserted well. Please don't submerge this unit into
water.
6.Are the probes and wires waterproof?
Answer: Yes.
7.Does this unit have low/high temperature alarm function?
Answer: Yes
8.Is there any graphing or save of previous cook data?
Answer: It can only display the current cooking data. Which can’t be saved
or download.
Q
BBQ
BBQ
GO~
Smart
Wireless
BBQ
Thermometer
Get
to
know
the
device
Current
Temperature
Value
Probe
Indicator
~
Probe
Sockets
USB
Charge
Plug
Temperature
Unit
( •c I
°F)
Battery
Indicator
Bluetooth
Indicator
----1-1--1---
Charging Indicator
(G})--+I+--
Power
Button
Pairing Button
Stop
Alarm
Button
Screen Rotation Button
(Tap
twice
to
rotate
screen)
Magnet
adsorption
base
Probe
with
cable
USB
Charge
Cable
(Length
:50cm)
This device
provides
4
probe
sockets, which enable
you
to
monitor
up to 4
food
at
same time.
Charge
the
device
This
device
use a
built-in
non-detachable
lithium
battery,
usable
charging
and
power
supply.
Please
note
that:
0
The
battery
cannot
be removed.
8 It
takes
about
two
hours
to
fully
recharge.
Download
the
APP
Search
the
keyword
"bbq
go"
in
Appstore
or
Google
Play,
or
scan
the
following
QR
code
with
your
phone.
Download and
install
it
for
free.
Make
sure
your
phone
meet
the
requirements:
iPhone
4S,
and
later
models;
iPod touch 5th, ipad 3rd
generations
and
later
models,
all ipad
mini;
Android
devices
running
version
4.4
or
later, with
blue-tooth
4.0 module.
1~1
BBQ
GO
APP
Install the
probes
The
device
will
keep
scanning
the
sockets
when its
power
is
switched
on, the Probe
Indicators
will
blink
one
by
one
from
1 to 4
where
probes
are
plugged
in.
Then
insert
the
probes
into
the
food,
make
sure
the
front
tip
of
the
probe
is
in
the
center
of
the
food
to
get
accurate
temperature.
Pair
with
your
phone
0
Press
and hold
the
power
button on the
device
for
3
seconds
to
power
it
on.
Bluetooth
Indicator
8 Keep
the
bluetooth
switch
of
your
phone
on.
8
Launch
the app, and
follow
the
instructions
•®'d:l@D
in
the
app
to
pair
and
activate
the
device.
0
Connected
successfully.
•bM•
Once
paired
the device with
your
phone,
you
don't
need
to do
it
again,
unless
you
change to
other
phones.
To Next Page
Need help?
General
