Innomed Medical Heart Screen 60G User Manual (English)

Questions and Answers:

N
nicholaspruittSep 8, 2025
What causes excessive baseline movement in Innomed Medical Equipment?
- J
  James AtkinsonSep 9, 2025
  Excessive baseline movement in Innomed Medical Equipment can be caused by the amplifier’s too great time constant and high-impedance parts; it is possible, that the multiplexers before the ADC or the DC isolating capacitors are damaged. Check and repair the amplifier card according to the documentation. If necessary, replace the HS80G card. It may also be caused by condensing humidity. Check if it was caused by condensing humidity.
J
jessicathomasAug 23, 2025
What to do if my Innomed Medical Equipment device does not turn on?
- K
  Kevin KellyAug 23, 2025
  If your Innomed Medical Equipment device doesn't turn on, it could be due to several reasons: * The batteries are completely discharged: Check the battery and its charge state. * The battery-protecting fuse has burned out: Replace the fuse and try to find the reason for the burn-out and fix it. * The battery is damaged: Replace the battery if it cannot be fixed. * The cable to the power switch is damaged or the connection to the power switch has slipped off: Check the cables and the connections. * The soldering is not satisfactory: Check the soldering on the digital part of the Main Board. Resolder the IC’s with the exception of the processor. If it cannot be repaired, replace the card.
R
russochristinaAug 25, 2025
What to do if the keys are not operational on my Innomed Medical Equipment device?
- S
  Sherry PottsAug 25, 2025
  If the keys on your Innomed Medical Equipment device are not working, check the cables and connections. If the cables and connections are fine, the keyboard card, or the Main Board or Interface Board could be damaged. Check the keys according to the connection diagram. If any of them are damaged, replace the keyboard. Check the Main Board and the Interface Board with another keyboard. Check the soldering and the keyboard control signals on the Main Board and the Interface Board. If it cannot be repaired, replace the damaged card.
M
Marcus ReynoldsAug 27, 2025
What to do if the "CHARGE" LED is not on after connecting the charging adapter to my Innomed Medical Equipment device?
- R
  Rhonda FitzgeraldAug 27, 2025
  If the "CHARGE" LED is not on after connecting the charging adapter to your Innomed Medical Equipment device, check the charging adapter cable and connection. Also, ensure that the keyboard connection is satisfactory. Check the „CHARGE” LED on the keyboard to rule out keyboard damage. Finally, the charging circuit might be damaged, so check the charging circuit.
D
Dawn BrownAug 27, 2025
Why is there no effect from the mains filter (50 or 60Hz) on my Innomed Medical Equipment device?
- M
  Miguel LopezAug 27, 2025
  If the mains filter (50 or 60Hz) has no effect on your Innomed Medical Equipment device, it may be because the noise is not appropriate for the mains frequency, or the environment noise is too great. Check the mains frequency and the environment for electromagnetic noise.
U
uriveraAug 29, 2025
Why is only one side of the LCD operational on my Innomed Medical Equipment device?
- D
  David HoganAug 29, 2025
  If only one side of the LCD is operational, or nothing is visible on your Innomed Medical Equipment device, but the QRS sound is audible, the cable between the Interface Board and the Main Board may be damaged, the Main Board may be damaged, or the LCD may be damaged. Check the connecting ribbon cable, the soldering on the LCD, and the connection at the end of the ribbon cable.
E
Erica PetersonSep 10, 2025
What causes parts of the printed picture to be faded on Innomed Medical Equipment?
- B
  Bethany CareySep 10, 2025
  If parts of the printed picture are faded on your Innomed Medical Equipment, the rubber roll may not tighten evenly on the burning head, or there may be a problem with paper quality or burning voltage. Check paper quality, and the burning voltage (HEAD_POWER) and burning time. In case of printer head problem, replace it.
V
victorcruzSep 7, 2025
What to do if the printed curve is missing along a horizontal line on Innomed Medical Equipment?
- J
  Jennifer NavarroSep 7, 2025
  If the printed curve is missing along a horizontal line on your Innomed Medical Equipment, the printer head may be dirty or a pixel has burnt out on the burning head. Clean the printer burning head with alcohol. If this does not solve the problem, replace the entire printer head.
E
Eric JacksonSep 4, 2025
How to troubleshoot serial line connection issues with Innomed Medical Equipment?
- B
  Brian MurphySep 4, 2025
  If the serial line connection is not working on your Innomed Medical Equipment, the Innobase or device software version might not be appropriate. Check the Innobase version and the Innobase software module version. Also, PC settings may not be appropriate, or the serial cable could be damaged, or the device’s serial line circuit could be damaged. Check PC settings, the serial cable, and the device serial circuit.
C
charlesirwinSep 5, 2025
What causes several ECG channels to be noisy on Innomed Medical Equipment?
- S
  stewartanthonySep 5, 2025
  If several ECG channels are noisy on your Innomed Medical Equipment, the environment noise may be too great, the mains ground protection conductor may be damaged, or the amplifier may be generating noise. Check the environment for electromagnetic noise. Check the mains ground protection conductor continuity to the device charging adapter connection input point (-). Check and repair the amplifier card according to the documentation.