Why is the BATTERY LED lit and beeping on my Innova OnLine UPS?
If the BATTERY LED is lit and there's an audible alarm sounding every 4 seconds on your Innova UPS, the input voltage and/or frequency are out of tolerance. Check the input power source, the building wiring, and ensure the input breaker is closed.
What to do if my Innova OnLine has an output overload?
If your Innova UPS indicates an output overload, examine the connected loads and remove any non-critical devices. Also, verify if any of the connected loads have failed.
What to do if Innova OnLine shows ambient over temperature?
If your Innova UPS indicates an ambient over temperature, check the environment ventilation.
What causes heatsink over temperature fault in Innova UPS?
A heatsink over temperature fault in your Innova UPS is caused by the inside temperature of the UPS being too high. Check the ventilation of the UPS and the ambient temperature.
What to do if Innova UPS reports a fan failure?
If your Innova UPS reports a fan failure, check if the fan is running normally.
What to do if my Innova UPS shows 'Battery Disconnected'?
If your Innova UPS displays 'Battery Disconnected', perform a battery test to confirm the issue. Check that the battery bank is correctly connected to the UPS and that the battery breaker is turned on.
Why is the emergency supply period shorter than nominal value on my Innova UPS?
If the emergency supply period of your Innova UPS is shorter than the nominal value, it could be due to batteries not being fully charged or defective batteries. Charge the batteries for at least 12 hours and then check their capacity.
What to do if Innova UPS has an output short circuit?
If your Innova UPS experiences an output short circuit, remove all connected loads. Turn off the UPS, then check both the UPS output and the loads for any short circuits. Make sure the short circuit is resolved before turning the UPS back on.
Why Innova OnLine has no indication even though connected to mains?
If your Innova UPS has no indication and no warning tone, even when connected to the mains power supply, it indicates no input voltage. Check the building wiring and input cable, and ensure the input breaker is closed.
What causes bypass overload fault in Innova UPS?
A bypass overload fault in your Innova UPS is caused by an overload. You should check the connected loads, remove some non-critical loads, and check if some loads are failed.
General| Frequency | 50/60Hz |
|---|---|
| Operating Temperature | 0-40°C |
| Output Voltage | 220/230VAC |
| Battery Type | Sealed Lead-Acid (SLA) |
| Communication Interface | USB, RS232 |
| Humidity | 0-90% non-condensing |
Safety instructions for installing the UPS unit by qualified personnel.
Safety precautions during UPS operation, including mains cable and earth connections.
Warnings regarding hazardous voltages and servicing by qualified personnel.
Guidelines for transporting and storing the UPS in its original packaging.
Lists safety and EMC standards applicable to the UPS product.
Highlights key features like double-conversion technology and output power factor.
Details input and output voltage, frequency, and power ratings.
Specifies temperature, humidity, and altitude limits for operation.
Provides backup time estimates for different load percentages.
Lists physical dimensions and net weight for different models.
Instructions on moving, unpacking, and inspecting the UPS for damage.
General installation notes regarding ventilation, condensation, and mounting brackets.
Cable cross-section and protective device specifications for installation.
Step-by-step guide for connecting external battery packs to the UPS.
Explanation and connection of the Emergency Power Off (EPO) port.
Describes the UPS control panel, LCD, and LEDs for status indication.
Details various operating modes like Line, Battery, Bypass, and HE mode.
Procedures for powering the UPS on and off, with and without utility power.
Explains navigation through menus and submenus on the UPS LCD display.
Introduction and setting instructions for the High Efficiency (HE) mode.
Introduction and setting instructions for the Converter mode.
Explains N+X redundancy and parallel connection of UPS units.
Lists problems, possible causes, and remedies for warning indications.
Lists problems, possible causes, and remedies for fault indications.
Addresses issues without specific indication, and provides info for service calls.
Details USB, dry contact, and intelligent slot interfaces for communication.
Information about WinPower monitoring software and its installation.
To Next Page