Why is there no sound from the subwoofer on Insignia Amplifier?
If there is no sound from the subwoofer on your Insignia Amplifier while playing a Dolby Digital, DTS, or other source signal, check if "SW" in "Speaker Setting" is set to "NONE". If so, change the setting to "YES".
Why is there no sound from the surround center speaker on Insignia Amplifier?
If there is no sound from the surround center speaker on your Insignia Amplifier, ensure that "Surround center" in "Speaker Setting" is not set to NONE. Also, the source or the listen mode selected may not contain surround center signals, so select "6 stereo" or another appropriate listen mode.
What to do if Insignia Amplifier fails to turn on?
If your Insignia Amplifier fails to turn on, it could be due to several reasons. First, ensure the power cord is firmly connected. If that's not the issue, the protection circuitry might have been activated. In this case, check all speaker wire connections to make sure they are secure and not touching anything else. Finally, if the unit has been exposed to a strong electric shock, set it to standby mode, disconnect the power cord, wait 30 seconds, and then plug it back in.
Why is there no sound from the surround speakers on Insignia Amplifier?
If there is no sound from the surround speakers on your Insignia Amplifier, ensure that the output level of the surround speakers is not set to minimum; if it is, raise the output level. Also, check that "SURR LR" in "Speaker Setting" is not set to NONE. If you're playing a monaural source with "2 STEREO", press "DSP" or "2/6STEREO" to turn on the sound fields or select "6 CH STEREO" mode.
Why is there no sound from the center speakers on Insignia Amplifier?
If there's no sound from the center speakers of your Insignia Amplifier, check if the output level of the center speaker is set to minimum and raise it. Also, verify that "CENTER" in "Speaker Setting" is not set to NONE. Finally, if 2ch Stereo is selected, switch to "6 stereo", another DSP mode, or an appropriate listen mode.
How to fix distortion on Insignia Amplifier?
If you are experiencing distortion on your Insignia Amplifier, adjust the antenna position to eliminate multipath interference.
How to fix noisy FM stereo reception on Insignia Amplifier?
Noisy FM stereo reception on your Insignia Amplifier can occur if the transmitter is too far away or the antenna input is poor. Check the antenna connections and consider using a high-quality directional FM antenna. You can also try using the manual tuning method.
Why can only one speaker be heard on Insignia Amplifier?
If you can only hear sound from one speaker on your Insignia Amplifier, the cable connections may be incorrect. Connect the cables properly. If the problem continues, the cables might be defective.
How to fix humming sound on Insignia Amplifier?
To address a humming sound from your Insignia Amplifier, firmly connect the audio plugs. If the problem persists, the cables may be defective.
What to do if Insignia Amplifier suddenly turns off automatically?
If your Insignia Amplifier suddenly turns off automatically with no sound or display, it's likely due to the internal temperature becoming too high, which activates the overheat protection circuitry. Wait about 1 hour for the unit to cool down, and then turn it back on.
General| Channels | 2 |
|---|---|
| Frequency Response | 20Hz - 20kHz |
| Type | Hybrid Tube Amplifier |
| Input Impedance | 47k Ohms |
| Power Supply | AC 120V, 60Hz |
| Impedance | 8 Ohms |
| Inputs | RCA |
| Outputs | Speaker terminals |
| Power Output | 40W per channel |
Lists all the items included in the package with the receiver unit.
Explains how to connect external audio and video devices to the receiver.
Details the process of connecting digital audio sources like optical and coaxial.
Instructions on how to connect speakers to the receiver unit.
How to configure speaker settings like size (Large/Small) and presence (None).
How to fine-tune the volume level for each individual speaker.
Using test tones to automatically balance speaker output levels for optimal listening.
How to choose audio/video sources and manage multiple video devices.
Provides solutions for common problems like unit failure, no sound, or display issues.
Troubleshooting tips for tuner reception problems and remote control malfunctions.
Procedure to reset all unit parameters to their factory default settings.
To Next Page
