Integra MEDIACLAVE 10 - User Manual

136968_V01_QSG_MEDIACLAVE_10_30_EN.docx 1/6
Quick Start Guide MEDIACLAVE 10/30 Media Sterilizer
This quick start guide is intended to provide a quick overview of your MEDIACLAVE’s
(MC) key features and to offer basic instructions for getting started. For
detailed
information, please refer to the operating instructions (OI)
that can be found at
www.integra-biosciences.com in different languages.
Intended use
This is a general-purpose laboratory instrument. Any use of this instrument in a medical or IVD setting
is the sole responsibility of the user. MEDIACLAVE 10/30 is used for the preparation and sterilization
of media and can easily be converted to a water bath (or for MC10 only to an autoclave for media
sterilization in glassware).
Safety information
Regardless of the listed safety notes, all locally applicable regulations must be observed.
1) This product may only be operated in a secure, protected network with trustworthy clients.
2) MEDIACLAVE may only be used by properly trained personnel in a manner specified by
INTEGRA Biosciences.
3) In error case the instrument must not be used, e.g. if the pressure value is not displayed or above
1.7 bar or hot steam is released from the safety valve. There is the risk of burns or explosion.
The instrument must be immediately switched off and separated from electricity supply. Stay
away from the device.
4) Observe the hazard warnings on the device. Caution is required when opening ports or the vessel
lid (potential risk of delay in boiling). Always wear safety goggles and oven gloves.
5) The hoses may get hot. Do not touch the hoses during operation.
6) Servicing work and repairs may only be performed by INTEGRA Biosciences or an authorized
after-sales service member.
7) It is mandatory that a service is carried out at least once a year or after 1000 sterilization cycles
(whatever is reached first).
Getting started
Install the instrument on a horizontal surface according to the IQ (PN 136951) and OQ (PN
136952) documents.
a. Safety cover
b. Safety valve
c. Dispense port
d. Vessel lid
e. Temperature probe for media
f. Adding port
g. Safety cover lock
h. Operating panel
i. Main switch
j. USB port
k. Printer (optional)
Switch on/off:
Press the main switch.
Switch on the device. In the MAIN MENU, three options are accessible:
• SELECT PROGRAM: To define and execute a program.
• MAINTENANCE: To drain or fill the vessel, automatically clean the
device and perform the safety valve tests.
• SYSTEM PARAMETER: To configure general device parameters,
make a backup to USB, etc..
k
d
e
f
g
a
b
c
h
i
j

Summary

Intended Use

Safety Information

Getting Started

Switch On;Off Operation

Instructions for powering the MEDIACLAVE device on and off using the main switch.

Main Menu Navigation

Overview of the three main menu options: Select Program, Maintenance, and System Parameter.

Initial Setup and Configuration

Language Selection

Procedure to navigate system parameters and select the desired language.

Media Preparation Programs

Preparing the Cuvette and Program

Steps for placing the cuvette and setting up a media preparation program.

Filling Coupling Water

Instructions for filling the vessel with conductive coupling water for sensor operation.

Selecting and Adjusting Programs

Guide to choosing predefined programs and customizing parameters for specific needs.

Running Standard or Chocolate Agar Programs

Program Execution Details

Dispensing Media

Instructions for dispensing media using the sterile dispensing port or external pumps.

Running Autoclave Program (MC10)

Steps for using the MEDIACLAVE in autoclave mode for media sterilization.

Running Water Bath Program

Procedure for operating the MEDIACLAVE in water bath mode for media preparation.

Maintenance Procedures

Daily Maintenance

Daily cleaning and rinsing procedures for the MEDIACLAVE device.

Monthly Maintenance

Monthly checks and cleaning procedures, including safety valve inspection.

Equipment Disposal

Integra MEDIACLAVE 10 Specifications

General

Brand	Integra
Model	MEDIACLAVE 10
Category	Laboratory Equipment
Language	English