Intermatic HB1116R User Manual

HB1116R OUTDOOR TIMER
INSTRUCTIONS
Thank you for purchasing the HB1116R Outdoor Timer with Stake and Receptacles. Please read the instructions below,
before using this product:
Features
•Weather resistant cover with latch to secure up to six extension cords
• Six grounded outlets controlled by an easy-to-set timer
•Timer features two ON and OFF settings per day
• Unit can be wall mounted, or used with easy-to-install ground stake
• Added safety features include grounded cord and 15 Amp circuit breaker
• Manual override switch.
Timer Instructions (See Fig. 1)
1. Insert ON (Green) trippers and OFF (Red) trippers into dial at desired ON
and OFF times.
2. Turn dial clockwise ( ) one or more complete revolutions until the
arrow head is aligned with the current time of day. Please note that AM
times are in the white section of the dial, and PM times are in the black
section of the dial.
3. Turn lamp or appliance ON.
4. Plug lamp or appliance cords into timer receptacles. Close and latch
timer cover to protect receptacles from moisture. Plug timer cord into
GFCI protected wall outlet if located outdoors.
Manual Override: Timer may be turned ON or OFF manually, by turning the over-
ride knob counterclockwise ( ). The timer will resume the next scheduled ON and OFF cycle automatically. See Figure 1.
Circuit Breaker: If unit does not function properly, the circuit breaker may have been activated. To reset, unplug the timer
from power source. Check to make sure the combined load of the lamps or appliances does not exceed the rated capacity
of the timer. If so, disconnect items until the electrical load is within the prescribed limits. Press the circuit breaker button to
reset. Plug timer into outlet and test by turning the manual override knob counterclockwise. See Figure 1.
NOTE: Whatever timer setting(s) are chosen, the setting(s) will apply to all 6 receptacles.
Wall Mounting the Timer: If timer is mounted on a wall, it must be at least 3 feet above the ground.
Stake Mounting: Place tabs on stake over the retention holes on the back of the timer. Push up on stake until tabs lock in
place. See Figure 2. The stake should be inserted in the ground up to the barrier on the stake. See Figure 3. DO NOT
DRIVE THE STAKE INTO THE GROUND. In order to avoid potential hazard, the extension cord should be clipped into the
stake as shown in Figure 4. This will keep the plugs off the ground.
Latching the cover: Hold cover and rear of unit with both hands and press firmly until latch snaps into place. (Fig. 5)
NOTE:
Wall Receptacle Cover: In order to meet the 2002 National Electric Code you should use a receptacle cover that protects
your outdoor receptacle when your timer is plugged in. Recommended for use are Intermatic Model WP1100C or for heavier
cords sets, Models WP1110C or WP1150C.
Electrical Ratings
15 Amp Resistive (heater), 1800 Watts
15 Amp Tungsten (Incandescent), 1800 Watts
120 Volts AC, 60 Hz
•
1
1
7
6
5
4
3
2
8
9
10
11
•
•
•
•
•
•
•
•
•
•
•
2
2
1
11
10
9
8
7
6
5
4
3
2
1
•
•
•
•
•
•
•
•
•
•
•
•
AM
AM
TIME OF DAY
HEAVY DUTY
3
2
1
PM
PM
Manual Knob
Time-Of-Day
Arrow
OFF Tripper
RED
ON Tripper
GREEN
Circuit
Breaker
Tripper
Storage
Mounting stake tabs fit
into holes on back of timer.
Retention
Holes
Push stake in
ground to barrier
Figure 1
Figure 2
Figure 3
Clip in stake
holds cord
Figure 4
Figure 5

Intermatic HB1116R Specifications

General

Brand	Intermatic
Type	Mechanical Timer
Voltage	120V
Amperage	15A
Resistive Amperage	15A
Inductive Amperage	10A
Horsepower	1/2 HP
Programmable	Yes
Number of Programs/On-Off Settings	48
Number of Trippers	2
Display	Analog
Minimum Time Setting	30 minutes
Maximum Time Setting	24 hours
Enclosure	Plastic
Outlets	1
Indoor/Outdoor	Indoor
Mounting	Wall
Time Interval	30 minute intervals

Summary

Timer Operation and Settings

Setting the Timer

Insert ON (Green) and OFF (Red) trippers into the dial at desired times. Turn dial clockwise until arrow aligns with current time.

Manual Override

Turn the override knob counterclockwise to manually turn the timer ON or OFF. The timer will resume scheduled cycles automatically.

Circuit Breaker Reset

Unplug timer, check load capacity, and press the circuit breaker button to reset if unit fails to function.

Installation and Mounting

Stake Mounting

Place tabs on stake over timer retention holes, push stake into ground up to barrier, and clip extension cord to stake.

Wall Mounting

If mounting on a wall, ensure the timer is positioned at least 3 feet above the ground.

Cover Latching

Hold the cover and rear of the unit firmly with both hands and press until the latch snaps into place.

Product Specifications

Electrical Ratings

15 Amp Resistive (heater) / Tungsten (Incandescent), 1800 Watts, 120 Volts AC, 60 Hz.

Safety and Warranty Information

General Safety Precautions

Do not modify or repair. Avoid wet conditions. Store indoors when not in use. Do not exceed electrical load ratings.

Limited One Year Warranty

Covers defects in workmanship for one year from purchase. Applies only to the original purchaser and is not transferable.