How to fix white lines on Intermec Printer?
White lines appearing along the paper web in your Intermec Printer's output can be attributed to a couple of issues. The printhead might be dirty, in which case cleaning the printhead is the suggested solution. Alternatively, there might be missing dots on the printhead, which would necessitate replacing the printhead.
Why is the printout on my Intermec Printer so weak?
If you're experiencing an overall weak printout on your Intermec Printer, there are several potential causes. First, check if the Paper Type setup is correct and change the setup if needed. A low contrast setup could also be the issue, so adjust that setting. The printhead pressure might be too low, requiring adjustment. In some cases, a worn printhead can cause this problem, necessitating a replacement. Lastly, the wrong printhead voltage could be the culprit, which would require replacing the CPU board.
Why is my Intermec Printer printing too dark?
An overall dark printout on your Intermec Printer can stem from several factors. Ensure that the Paper Type setup is correct and change it if necessary. If the contrast setup value is too high, adjust it accordingly. Also, check the printhead pressure; if it's too high, you'll need to adjust it. In some cases, the wrong printhead voltage can cause this, requiring a replacement of the CPU board.
What to do if the paper feed is not working properly on my Intermec Printer?
If the paper feed on your Intermec printer isn't working properly, here's what you can check: * If the media characteristics have changed, perform a TESTFEED. * Verify and adjust the start- and stop adjust values. * Ensure the Media Type setup is correct. * Check the sensor position and adjust if needed. * Clean the paper guides to remove any dirt or blockages. * If the sensors are faulty, replace them.
Why is there excessive bleeding on my Intermec Printer's printouts?
Excessive bleeding on printouts from your Intermec Printer could be due to a few reasons. First, verify that the Paper Type setup is correct and change it if needed. A contrast setup value that is too high can also cause bleeding, so adjust the setting. Additionally, check the printhead pressure and adjust if it's too high. In some instances, a faulty energy control can be the cause, which would require replacing the CPU board.
What causes a large part of a dot line to be missing on my Intermec Printer?
If a large part of a dot line is missing from printouts on your Intermec Printer, it could be due to a few reasons. Check the X-start or Width setup and change the setup if it is wrong. The printhead may be failing, requiring a replacement. Finally, a failing strobe signal could be the issue, which would require checking the CPU-board.
Why does my Intermec Printer have weak spots on the printout?
Weak spots in the printout of your Intermec printer can be caused by several factors. Foreign particles on the paper can interfere with printing, so clean or replace the paper. Poor paper quality can also lead to weak spots; consider using Intermec paper. A worn printhead or worn platen roller can also cause this issue, so replace the printhead or check/replace the platen roller.
Why is the printout missing along the inner edge of my Intermec Printer?
If the printout is missing along the inner edge on your Intermec Printer, here are a few things to consider: * Bad paper alignment may be the issue, so adjust the paper alignment. * If you're using a small core and the hanger is in the upper position, move the hanger to the lower position. * The X-start setup value might be too low, so increase it.
What to do if the printout is weaker on one side of my Intermec Printer?
If the printout is weaker on one side when using your Intermec Printer, it may be due to uneven printhead pressure. To resolve this, adjust the arm alignment.
Why are there dark lines along the paper web on my Intermec Printer?
If you're seeing dark lines along the paper web when using your Intermec Printer, it's likely due to foreign objects on the printhead. Cleaning the printhead should resolve this issue.
General| Resolution | 203 dpi (8 dots/mm) |
|---|---|
| Function | Label Printing |
| Compatibility | Intermec printers |
| Print Method | Direct Thermal / Thermal Transfer |
| Max Print Width | 104 mm (4.1 in) |
| Max Print Speed | 6 inches per second |
| Connectivity | USB, RS-232 |
| Operating System Compatibility | Windows |
| Media Type | Labels, Tags |
| Memory | 8 MB SDRAM, 4 MB Flash |
To Next Page
