What to do if Intermec Barcode Reader has white lines along media path?
If you notice white lines along the media path, it could be due to a dirty printhead; try cleaning it. Alternatively, there might be missing dots on the printhead, which would mean the printhead needs to be replaced.
Why is the printout on my Intermec Printer so weak?
If you're experiencing an overall weak printout on your Intermec Printer, there are several potential causes. First, check if the Paper Type setup is correct and change the setup if needed. A low contrast setup could also be the issue, so adjust that setting. The printhead pressure might be too low, requiring adjustment. In some cases, a worn printhead can cause this problem, necessitating a replacement. Lastly, the wrong printhead voltage could be the culprit, which would require replacing the CPU board.
Why is my Intermec Printer printing too dark?
An overall dark printout on your Intermec Printer can stem from several factors. Ensure that the Paper Type setup is correct and change it if necessary. If the contrast setup value is too high, adjust it accordingly. Also, check the printhead pressure; if it's too high, you'll need to adjust it. In some cases, the wrong printhead voltage can cause this, requiring a replacement of the CPU board.
What to do if the paper feed is not working properly on my Intermec Printer?
If the paper feed on your Intermec printer isn't working properly, here's what you can check: * If the media characteristics have changed, perform a TESTFEED. * Verify and adjust the start- and stop adjust values. * Ensure the Media Type setup is correct. * Check the sensor position and adjust if needed. * Clean the paper guides to remove any dirt or blockages. * If the sensors are faulty, replace them.
Why is there excessive bleeding on my Intermec Printer's printouts?
Excessive bleeding on printouts from your Intermec Printer could be due to a few reasons. First, verify that the Paper Type setup is correct and change it if needed. A contrast setup value that is too high can also cause bleeding, so adjust the setting. Additionally, check the printhead pressure and adjust if it's too high. In some instances, a faulty energy control can be the cause, which would require replacing the CPU board.
What causes a large part of a dot line to be missing on my Intermec Printer?
If a large part of a dot line is missing from printouts on your Intermec Printer, it could be due to a few reasons. Check the X-start or Width setup and change the setup if it is wrong. The printhead may be failing, requiring a replacement. Finally, a failing strobe signal could be the issue, which would require checking the CPU-board.
Why Intermec Barcode Reader printout weaker on one side?
A printout that is weaker on one side is caused by uneven printhead pressure. Adjust the arm alignment to correct this.
What if large part of dot line missing on Intermec Barcode Reader?
If a large part of the dot line is missing, it could indicate a failing printhead, which means you should replace it. Alternatively, it could be due to a failing strobe signal, in which case you should check the CPU-board.
Why is my Intermec Barcode Reader printout overall dark?
An overall dark printout on your Intermec Barcode Reader can stem from several issues. The media grade might be incorrect, so try changing the parameter. A contrast value that's too high could also be the cause, so you should change the parameter. Additionally, excessive printhead pressure may be the culprit, requiring an adjustment. In some instances, the wrong printhead voltage may be the reason, necessitating a CPU board replacement.
Why are there dark lines along the paper web on my Intermec Printer?
If you're seeing dark lines along the paper web when using your Intermec Printer, it's likely due to foreign objects on the printhead. Cleaning the printhead should resolve this issue.
General| Resolution | 203 dpi (8 dots/mm) |
|---|---|
| Function | Label Printing |
| Compatibility | Intermec printers |
| Print Method | Direct Thermal / Thermal Transfer |
| Max Print Width | 104 mm (4.1 in) |
| Max Print Speed | 6 inches per second |
| Connectivity | USB, RS-232 |
| Operating System Compatibility | Windows |
| Media Type | Labels, Tags |
| Memory | 8 MB SDRAM, 4 MB Flash |
Copyright and proprietary information for the printer manual.
List of registered trademarks associated with the printer.
Regulatory compliance statement for the United States regarding radio frequency interference.
Regulatory compliance statement for Canada regarding radio noise emissions.
General safety regulations for machinery operation in Germany.
Compliance statement for electromagnetic compatibility in the EU.
Essential safety guidelines to follow during printer operation and maintenance.
Information regarding labels on the printer identifying model, serial number, and approvals.
Guide to creating custom label formats using the Fingerprint language.
Instructions for label creation using the Direct Protocol.
Steps for safely removing the printer from its packaging.
Description of the printer's front panel components and controls.
Description of the printer's rear panel connectors and switches.
Details on the printer's internal area for loading media rolls.
Overview of the printer's components responsible for printing.
Information on connecting the printer to power and external devices.
Explanation of the printer's lights, display, and keyboard.
How startup files determine the printer's behavior on power-up.
Information on using electronic keys for specific printer functions.
Details on using memory cards for additional fonts or firmware.
Procedure for powering on the printer and initial checks.
Understanding messages shown during the printer's initialization.
Procedure for loading media for manual tearing at the tear bar.
Using Quick-Load guides for easier tear-off media loading.
Procedure for loading media for peel-off label dispensing.
Loading media from an external source like fanfold tickets.
Instructions for loading thermal transfer ribbons into the printer.
Overview of printer setup parameters like communication and print speed.
Printer's factory default configuration settings.
Detailed configuration options for serial communication, media, and print defines.
Methods to access the printer's setup menu.
How to use the keyboard keys to move through setup menus.
Diagrams illustrating the structure of the setup menus.
Explains Intermec Shell as a startup program for printer functions.
Steps to launch and enter the Intermec Shell environment.
Describes the menus and options available within Intermec Shell.
Procedure for setting up communication via a terminal program.
Overview of optional hardware for printer customization.
Information on the Direct Thermal Printing model.
Description of different side door options affecting media access.
Details on the optional unit for peel-off operation.
Description of the optional rotating hub for media rolls.
Adapter for using 3-inch core media rolls with the supply hub.
Optional guides to simplify media loading.
Sensor to detect if a label has been removed.
Device for easy setup via bar codes.
Function to set and maintain printer date and time.
Details on optional interface boards for expanded connectivity.
A guide to diagnosing and resolving common printer issues.
Procedure for cleaning the printer's printhead.
Instructions for cleaning the printer's exterior surfaces.
How to clean the guides that direct the media.
Steps for replacing the printer's printhead.
Adjusting the pressure arm for media less than full width.
Aligning the sensor for accurate media gap detection.
Adjusting the pressure applied by the printhead.
Adjusting the shaft to prevent ribbon wrinkling.
Specifications and technical details of the EasyCoder F4 printer.
Details on compatible media types, sizes, and properties.
Specifications for non-adhesive media strips.
Specifications for self-adhesive media strips.
Specifications for self-adhesive label media.
Specifications for tickets with detection gaps.
Specifications for tickets with black marks for detection.
Specifications for thermal transfer ribbons.
Information on various interface board options for the printer.
Details on the standard serial communication port.
Details on the Universal Serial Bus interface.
Information on the optional board providing two extra serial ports.
Details on the optional parallel interface board.
Information on the optional industrial interface board.
Details on the optional Ethernet network interface board.
Guide to setting up the printer using a bar code wand.
Bar codes for configuring serial communication parameters.
Bar codes for adjusting media feed start and stop points.
Bar codes for adjusting print contrast.
Bar codes for printing test labels.
Bar codes for setting media width.
Bar codes for setting media length.
Bar codes for selecting media types.
Bar codes for setting print speed.
Bar codes for selecting paper types.
To Next Page
