Intex 602 - User Manual

Questions and Answers

T
Tiffany KnightAug 13, 2025
How to fix Intex Water Pump filter motor that fails to start?
- E
  Elizabeth RiosAug 13, 2025
  If the Intex Water Pump filter motor fails to start, first, ensure the filter cord is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. Next, try resetting the circuit breaker. If it trips repeatedly, there may be an electrical system defect, so turn off the breaker and consult an electrician. Finally, the motor might be too hot, so allow it to cool down.
E
elizabeth35Aug 17, 2025
What to do if Intex 602 Water Pump doesn’t pump water or flow is very slow?
- D
  Douglas SuttonAug 17, 2025
  If the Intex Water Pump doesn’t pump water or the flow is very slow, check for obstructions in the intake hose. Clear any obstructions by discharging it inside the pool wall. Ensure there isn't an air leak on the intake line by tightening hose clamps and checking for hose damage, also check pool water level. Replace the cartridge if there's scale or buildup. If the pool is excessively dirty, clean the cartridge more often. Ensure the nozzle is installed at the upper position of the pool inlet and the strainer at the lower position of the pool outlet. Also, confirm the pool inlet air adapter is connected to the pool inlet upper fitting.
J
James RussoAug 20, 2025
Why doesn't my Intex Water Pump filter clean the pool?
- A
  ahickmanAug 21, 2025
  If your Intex Water Pump filter doesn't clean the pool effectively, start by adjusting the chlorine and pH levels, consulting your local pool supply store for guidance. Then, clean or replace the filter cartridge, checking it for holes and replacing it if damaged. If the pool is excessively dirty, operate the filter for longer periods. Also, ensure you clean the strainer screen at the inlet.
C
Catherine PalmerAug 25, 2025
How to stop small leak from air jet valve when Intex Water Pump is on?
- M
  maria08Aug 25, 2025
  If you notice a small leak from the air jet valve when the Intex Water Pump is on, it may be due to accessories attached to the water circulation line. Remove all accessories, such as solar mats, auto pool cleaners, or LED lights, from the water circulation line. Place the air jet valve cap over the air jet valve. Do not cover the air jet valve with the valve cap under normal situations or when the pump is operating.
C
Charles AlvaradoAug 28, 2025
How to fix Intex 602 Water Pump top cover leaking?
- J
  jennifersimsAug 29, 2025
  If the Intex Water Pump top cover is leaking, remove the cover and check for the O-ring. If it’s missing, replace it. Also, ensure that the cover and air release valve are tightened manually.
D
David PhelpsSep 1, 2025
How to remove air lock from Intex 602 Water Pump?
- L
  Lynn FisherSep 1, 2025
  To address an air lock in your Intex Water Pump, which is caused by air trapped in the pump housing and inlet hose, open the air release valve. Lift and lower the inlet hose until water starts flowing out of the air release valve, then close the valve.
K
Kimberly MarshallSep 5, 2025
What to do if Intex 602 hose is leaking?
- C
  Caitlyn GomezSep 5, 2025
  If the hose on your Intex Water Pump is leaking, first, try tightening or changing the hose clamps. If that doesn't work, check if the hose o-ring dislodged when connecting the hose and put it back into the groove. If the hose is broken, replace it with a new one.
L
Linda BrownSep 9, 2025
How to repair Pool Inlet Air Adaptor/Air Jet Valve leaking on Intex 602 Water Pump?
- M
  Michael SmithSep 9, 2025
  If your Pool Inlet Air Adaptor or Air Jet Valve is leaking, try these steps: * Tighten or reinstall the hose clamps. * Tighten the air jet valve and make sure it’s facing up. * Plug in the pump and run it for a few seconds, then unplug it; repeat this three times. * Remove the air jet valve, flush out any dirt with water, and replace the valve. * If none of these steps work, replace the air jet valve with a new one.