Intex Krystal Clear 601

Questions and Answers

G
Gary WagnerSep 23, 2025
How to remove surface debris using Intex Krystal Clear 601 Water Pump?
- C
  Cody CraigSep 23, 2025
  To remove surface debris, use an Intex pool skimmer.
S
Sheri WilliamsAug 23, 2025
Why Intex Krystal Clear 601 Water Pump doesn’t pump water or flow is very slow?
- T
  Tyler NicholsAug 25, 2025
  If your Intex Water Pump doesn't pump water or the flow is very slow, clear any obstructions in the intake hose by discharging it inside the pool wall. Ensure that hose clamps are tightened, inspect the hoses for any damage and check the pool water level. Replace the cartridge if needed, or clean the cartridge more often. Install the nozzle at the upper position of the pool inlet, and the strainer at the lower position of the pool outlet. Make sure the pool inlet air adaptor is connected to the pool inlet upper fitting.
R
Robert HumphreyAug 25, 2025
Why Intex Krystal Clear 601 doesn’t work?
- O
  odavisAug 26, 2025
  If your Intex Water Pump isn’t working, ensure the pool is filled to the correct water level. Clean the strainer screens at the pool inlet. Tighten the hose clamps and check the hose for damage. Clear any sticks or leaves in the intake hose. Open the release valve at the top of the pump.
I
ian07Aug 27, 2025
Why is my Intex Krystal Clear 601 Water Pump filter not cleaning the pool?
- C
  clayton21Aug 27, 2025
  If your Intex Water Pump filter isn’t cleaning the pool, you can try the following: * Adjust the chlorine and pH level; consult your local swimming pool supply stores. * Clean or replace the cartridge. * Check the cartridge for holes and replace it if damaged. * Operate the filter for longer periods. * Clean the strainer screen at the inlet.
K
Kimberly LoveAug 27, 2025
What to do if Intex Water Pump filter doesn’t pump water or flow is very slow?
- D
  dominiqueclarkAug 27, 2025
  If your Intex Water Pump filter isn’t pumping water or the flow is very slow, here are some things you can try: 1. Clear any obstructions in the intake hose by discharging it inside the pool wall. 2. Tighten hose clamps, check hoses for damage, and check the pool water level. 3. Replace the cartridge. 4. Clean the cartridge more often. 5. Install the nozzle at the upper position of the pool inlet, and the strainer at the lower position of the pool outlet. 6. Make sure the pool inlet air adaptor is connected to the pool inlet upper fitting.
C
Cheryl PerrySep 16, 2025
How to get rid of floating matter in water with Intex Water Pump?
- R
  rebeccacastilloSep 16, 2025
  To address floating matter in the water with your Intex Water Pump: * Correct the pH level; check with your pool dealer for advice. * Adjust the chlorine level. * Clean or replace your filter.
K
Kyle WalshSep 13, 2025
How to fix a top cover leaking on Intex Krystal Clear 601?
- J
  Jeffrey RangelSep 13, 2025
  To address a leaking top cover on your Intex Water Pump: * Remove the cover and check for the O-ring. * Tighten the cover or valve manually.
B
Brittney ClaySep 14, 2025
How to fix leaking pool inlet air adapter or air jet valve on Intex Krystal Clear 601?
- C
  Christine HullSep 15, 2025
  To fix a leaking pool inlet air adapter or air jet valve on your Intex Water Pump: * Tighten or reinstall the hose clamps. * Tighten the air jet valve and make sure it’s facing up. * Plug in the pump and run for a few seconds, then unplug; repeat 3 times. * Remove the air jet valve, flush dirt out with water, and replace the valve back. * Replace with a new air jet valve.
S
Sydney RogersSep 5, 2025
How to fix Intex Krystal Clear 601 Water Pump hose leaking?
- R
  ramosveronicaSep 5, 2025
  If your Intex Water Pump hose is leaking, try tightening or reinstalling the hose clamps. Ensure the o-ring is properly placed in the groove. If the leak persists, replace the hose with a new one.
B
Beth LesterSep 3, 2025
What to do if Intex Krystal Clear 601 doesn’t clean pool?
- R
  Ryan SullivanSep 3, 2025
  If your Intex Water Pump is not cleaning the pool effectively, adjust the chlorine and pH levels, consulting your local swimming pool supply store for guidance. Clean or replace the cartridge, checking it for holes and replacing it if damaged. Operate the filter for longer periods and clean the strainer screen at the inlet.