Intex Krystal Clear 601 User Manual

257
PO
SAVE THESE INSTRUCTIONS
English
(257PO) MODEL 601 FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 04/22/2016
Page 8
TROUBLESHOOTING GUIDE
• Filtercordmustbepluggedintoa3wireoutlet
 thatisprotectedbyaClassAGroundFault
Circuit Interrupter.
• Resetcircuitbreaker.Ifcircuitbreakertrips
repeatedly, your electrical system may have a
defect. Turn off circuit breaker and call an
electrician to correct the problem.
• Letmotorcooldown.
• AdjustthechlorineandpHlevel.Consultyour
local swimming pool supply stores.
• Cleanorreplacecartridge.
• Check the cartridge for holes. Replace if
damaged.
• Operatethefilterforlongerperiods.
• Cleanthestrainerscreenattheinlet.
• Clearanyobstructionsintheintakehoseby
discharging it inside pool wall.
• Tightenhoseclamps,checkhosesfordamage,
check pool water level.
• Replacecartridge.
• Cleancartridgemoreoften.
• Installthenozzleattheupperpositionofthe
pool inlet, and the strainer at the lower position
of the pool outlet.
• Make sure the pool inlet air adaptor is
connected to the pool inlet upper fitting.
• Fillpooltocorrectwaterlevel.
• Cleanstrainerscreensatpoolinlet.
• Tightenhoseclamps,checkhosefordamage.
• Clearanysticksorleavesintheintakehose.
• Openthereleasevalveattopofpump.
• Removecover&checkforO-ring.
• Tightencoverorvalve(Manually).
• Tightenorreinstallhoseclamps.
• Puttheo-ringbackintothegroove.
• Replaceanewhose.
• Openairreleasevalve,liftandlowertheinlet
hose until water starts to flow out of air release
valve, close air release valve.
• Tighten or reinstall hose clamps.
• Tightenairjetvalveandmakesureit’s
facing up.
• Pluginthepumpandrunforfewseconds,then
unplug, repeat 3 times.
• Removeairjetvalve,flushdirtoutwithwater
and replace valve back.
• Replaceanewairjetvalve.
FILTER MOTOR
FAILS TO START
FILTER DOESN’T
CLEAN POOL
FILTER DOESN’T
PUMP WATER OR
FLOW IS VERY SLOW
PUMP DOESN’T
WORK
TOP COVER
LEAKING
HOSELEAKING
AIRLOCK
POOL INLET AIR
ADAPTOR / AIR JET
VALVELEAKING
• Themotorisnotpluggedin.
• TheGFCIcircuitbreakeristripped.
• Motortoohotandoverload 
protection is shut off.
• ImproperchlorineorpHlevels.
• Filtercartridgeisdirty.
• Damagedcartridge.
• Excessivelydirtypool.
• Thestrainerscreenis
restricting the water flow.
• Cloggedinletordischarge.
• Anairleakontheintakeline.
• Scaleorbuilduponcartridge.
• Excessivelydirtypool.
• Dirtyfiltercartridge.
• Nozzleandstrainerconnectionare
reversed.
• Pool inlet air adaptor connected to
the wrong fitting.
• Lowwaterlevel.
• Strainerscreenpluggedup.
• Anairleakontheintakehose.
• Faultymotorortheimpelleris 
jammed.
• Anairlockinsidethecartridge 
chamber.
• O-ringmissing.
• Coverorairreleasevalvearenot
tight.
• Hoseclampsarenotwell-fitted.
• Hoseo-ringdislodgedwhen
connecting the hose.
• Hosebroken.
• There’sairtrappedinthepump 
housing and inlet hose.
• Hose clamps are not well-fitted.
• Air jet valve is not tight and
facing up.
• Air jet valve internal seal blocked.
• Air jet valve internal seal dirty.
• Air jet valve broken.
TROUBLE
CAUSE
SOLUTION

Intex Krystal Clear 601 Specifications

General

Brand	Intex
Model	Krystal Clear 601
Category	Water Pump
Language	English