Intex Krystal Clear SF90220T User Manual (English)

Questions and Answers:

J
john71Aug 22, 2025
Why won't my Intex Krystal Clear SF90220T Water Pump filter motor start?
- C
  Christopher BlackburnAug 22, 2025
  If the Intex Water Pump filter motor won't start, first ensure the line cord is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. Check if the GFCI/RCD circuit breaker has tripped and reset it. If it repeatedly trips, there may be an electrical system defect requiring an electrician. Also, the motor may be too hot, so let it cool down before restarting.
J
Jon JonesAug 23, 2025
What to do if Intex Krystal Clear SF90220T doesn't pump water or flow is very slow?
- L
  lnortonAug 23, 2025
  If your Intex Water Pump filter isn’t pumping water or the flow is very slow, there might be trapped air in the system – release the air according to the operating instructions section. Check for clogs in the inlet or discharge and clear any obstructions. Also, inspect the intake line for air leaks, tightening hose nuts and checking for damage, and ensure the pool water level is adequate. Backwash the filter if the pool is excessively dirty. If the sand media is clogged with dirt, remove about 1” of sand if necessary. Make sure the nozzle is at the upper position of the pool inlet, and the strainer at the lower position of the pool outlet. Remove any pool vacuuming device attached to the system line, if there is crusting or caking on the filtering sand surface.
D
Desiree ThompsonAug 25, 2025
Why my Intex Krystal Clear SF90220T Water Pump doesn't work?
- L
  lisa66Aug 26, 2025
  If your Intex water pump isn't working, start by checking the water level; ensure it's at the correct level. Next, inspect the strainer screens at the pool inlet for clogs and clean them if necessary. Also, check the intake hose for air leaks by tightening the hose nuts and inspecting the hose for damage. If these steps don't resolve the issue, the motor may be faulty or the impeller jammed.
B
Benjamin SalazarAug 26, 2025
How to fix Intex Krystal Clear SF90220T Water Pump filter motor that fails to start?
- C
  carlysinghAug 27, 2025
  If the Intex Water Pump filter motor won't start, ensure the line cord is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. Also, reset the GFCI/RCD circuit breaker; if it repeatedly trips, your electrical system may have a defect, so turn off the breaker and consult an electrician. Finally, the motor may be too hot; let it cool down before restarting.
K
Kimberly NealAug 27, 2025
What to do if my Intex Krystal Clear SF90220T Water Pump filter doesn't pump water or the flow is very slow?
- E
  Elizabeth VillanuevaAug 27, 2025
  If your Intex Water Pump filter doesn't pump water or the flow is very slow, first release any trapped air (refer to the operating instructions section). Next, clear any obstructions in the intake hose. After that, check for air leaks on the intake line by tightening hose nuts and inspecting for damage, also check the pool water level. If the pool is excessively dirty, backwash the filter. If the sand media is clogged with dirt, remove about 1 inch of sand if necessary. Ensure the nozzle and strainer connections are not reversed. Remove any pool vacuuming device attached to the system line. Finally, ensure the inlet threaded air connector is connected to the pool inlet upper hole.
Z
zfordAug 28, 2025
What to do if my Intex Krystal Clear SF90220T doesn’t work?
- J
  Jessica WhitneyAug 29, 2025
  If your Intex Water Pump isn’t working, ensure the pool is filled to the correct water level. Clean the strainer screens at the pool inlet. Tighten the hose nuts and check the hose for damage if there's an air leak on the intake hose. If these steps don't resolve the issue, it may be a faulty motor or jammed impeller.
M
Melissa MatthewsAug 30, 2025
How to improve cleaning performance of my Intex Krystal Clear SF90220T Water Pump?
- S
  Sydney FordAug 30, 2025
  If your Intex Water Pump filter isn’t cleaning the pool, adjust the chlorine and pH levels. Ensure there is filtering media in the tank, loading it with filter sand according to the sand loading instructions. Set the 6-way valve to the 'FILTER' position. If the pool is excessively dirty, operate the filter for longer periods. Also, clean the strainer screen at the inlet if it's restricting water flow.
C
Cheryl ReevesAug 31, 2025
How to troubleshoot timer issues on Intex Krystal Clear SF90220T?
- A
  Anthony StevensAug 31, 2025
  If the timer on your Intex Water Pump is inaccurate or can't be set, turn off the pump and restart 5 minutes later. Try re-setting the timer.
C
Catherine DeanSep 1, 2025
What to do if sand is flowing back into the pool from my Intex Water Pump?
- M
  Mrs. Madison OdomSep 1, 2025
  If sand is flowing back into your pool from your Intex water pump, it could be due to the sand being too small. Use only No. 20 silica sand with a particle size range of 0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75. Another cause might be a calcified sand bed, in which case you should change the sand.
G
gbrewerSep 3, 2025
How to solve Intex Krystal Clear SF90220T timer inaccurate or timer can't be set?
- D
  Douglas FreemanSep 3, 2025
  If the timer on your Intex water pump is inaccurate or cannot be set, try turning off the pump and restarting it 5 minutes later. If that doesn't work, re-set the timer.