Intex Krystal Clear 601

Questions and Answers:

W
William ManningSep 8, 2025
What to do if Intex Krystal Clear 601 Water Pump pool inlet air adaptor / air jet valve leaking?
- T
  Thomas AtkinsonSep 8, 2025
  If the pool inlet air adapter or air jet valve is leaking on your Intex Water Pump, tighten or reinstall the hose clamps. Tighten the air jet valve, ensuring it faces upwards. Plug in the pump and run it for a few seconds, then unplug; repeat this process three times. Remove the air jet valve, flush out any dirt with water, and replace the valve. If necessary, replace the air jet valve with a new one.
C
christinarobertsSep 7, 2025
How to fix Intex Krystal Clear 601 Water Pump top cover leaking?
- A
  andrea16Sep 7, 2025
  If the top cover of your Intex Water Pump is leaking, remove the cover and check for the O-ring. Tighten the cover or valve manually.
G
gcollinsAug 22, 2025
Why Intex Krystal Clear 601 filter motor fails to start?
- V
  victorramirezAug 22, 2025
  If your Intex Water Pump filter motor isn't starting, ensure the filter cord is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter. Also, try resetting the circuit breaker. If it trips repeatedly, there might be an electrical system defect requiring an electrician. Finally, allow the motor to cool down.
S
Shelley HughesSep 4, 2025
Why is the water colored with Intex Krystal Clear 601 Water Pump?
- D
  Diana NortonSep 4, 2025
  If you notice colored water when using your Intex Water Pump, adjust the pH level to the recommended level. Run the filter until the water is clear, and clean the cartridge frequently.
B
Beth LesterSep 3, 2025
What to do if Intex Krystal Clear 601 doesn’t clean pool?
- R
  Ryan SullivanSep 3, 2025
  If your Intex Water Pump is not cleaning the pool effectively, adjust the chlorine and pH levels, consulting your local swimming pool supply store for guidance. Clean or replace the cartridge, checking it for holes and replacing it if damaged. Operate the filter for longer periods and clean the strainer screen at the inlet.
P
Patrick TranSep 1, 2025
How to fix algae in my Intex Water Pump pool?
- O
  Oscar DuarteSep 2, 2025
  To address algae issues in your Intex Water Pump pool: * Super chlorinate with shock treatment and correct the pH to your pool store's recommended level. * Vacuum the pool bottom. * Maintain the proper chlorine level.
R
Ricky AndersonAug 31, 2025
How to remove floating matter in water with Intex Krystal Clear 601?
- R
  Robert MeyerAug 31, 2025
  If you observe floating matter in the water with your Intex Water Pump, correct the pH level and adjust the chlorine level. Clean or replace your filter.
M
margaret27Aug 30, 2025
How to fix air lock in Intex Water Pump?
- A
  Anthony MejiaAug 30, 2025
  To resolve an air lock in your Intex Water Pump, open the air release valve. Lift and lower the inlet hose until water starts to flow out of the air release valve, then close the air release valve.
T
Tammy HillAug 29, 2025
What to do if my Intex Water Pump doesn't work?
- C
  Christopher MarshallAug 29, 2025
  If your Intex Water Pump isn't working, try these steps: * Fill the pool to the correct water level. * Clean the strainer screens at the pool inlet. * Tighten hose clamps and check the hose for damage. * Clear any sticks or leaves in the intake hose. * Open the release valve at the top of the pump.
K
Kimberly LoveAug 27, 2025
What to do if Intex Water Pump filter doesn’t pump water or flow is very slow?
- D
  dominiqueclarkAug 27, 2025
  If your Intex Water Pump filter isn’t pumping water or the flow is very slow, here are some things you can try: 1. Clear any obstructions in the intake hose by discharging it inside the pool wall. 2. Tighten hose clamps, check hoses for damage, and check the pool water level. 3. Replace the cartridge. 4. Clean the cartridge more often. 5. Install the nozzle at the upper position of the pool inlet, and the strainer at the lower position of the pool outlet. 6. Make sure the pool inlet air adaptor is connected to the pool inlet upper fitting.