Intex CS7111 User Manual

SAVE THESE INSTRUCTIONS
Page 2
(189PO) MODEL CS7111 SALTWATER SYSTEM & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/28/2013
English
189
PO
S AVE THESE INSTRUCTIONS
English
Page 26
TROUBLESHOOTING GUIDE (continued)
INSUFFICIENT
CHLORINE
INSUFFICIENT
COPPERIONLEVEL
POOLISSTAINED
WHITEFLAKESIN
THE WATER
NOLEDDISPLAY
GREENHAIR
• Insufficient operating hours of the
Saltwater System.
• The salt level in the pool water is less
than 2000ppm. This is insufficient.
• Chlorine loss due to intense sunlight
exposure.
• The bather load has increased.
• Clogged or dirty electrolytic cell.
• High UV level exposure.
• Insufficient operating hours.
• The PH is too high.
• The bather load has increased.
• Clogged or dirty copper electrode.
• Copper electrode defective.
• High copper ion concentration.
• Excessive calcium hardness is
present in pool water.
• Nopowersupply.
• RCD/GFCIhasnotreseted.
• A power fuse has blown.
• LED failure.
• Incorrectswitching,presstwobuttons
( and ) together.
• High copper ion concentration.
• Increase the daily Saltwater System operating time.
See “Operating Instructions”.
• Check the salt level with the Test Kit. Adjust as
 needed.See“Salt&PoolWaterVolumes”.
• Use a pool cover when the pool is not in use and/or
when the unit is operating.
• Increase the daily Saltwater System operating time.
See “Operating Instructions”.
• Remove the cell for inspection, clean it if necessary.
See “Maintenance”.
• Cover the pool with a pool cover for 2 days with the
device running and then test the water using the test
strips.
• If the pool is clean and clear, add stabilizer to the
water and then test the water with the device running.
• Increase operating time per day. See
“Operating Instructions”.
• Use PH decrease chemical to adjust, contact
your local pool chemical store.
• Increase the operating time per day. See
“Operating Instructions”.
• Remove the cell for inspection, clean it if
necessary. See “Maintenance”.
• Contact Intex Service Center.
• Drainabout20%ofthepoolwaterandadd
fresh water to decrease the copper ion
concentration below 0.2ppm.
• Add aluminum sulfate: 1000 liters water need
around 2g (1000 gals need 0.27 ounce) or
aluminum potassium sulfate: 1000 liters water
 needaround3g(1000galsneed0.4ounce)to
pool.
• Usealemonbasedcleaningproduct
(preferably containing citric acid). Don’t scrub
with aggressive cleaning products because
this might etch the underlying surface.
• Drainabout20to25%ofthepoolwaterand
add fresh water to decrease the calcium
hardness. Inspect the electrolytic cell for scale
buildup. Clean the electrolytic cell if necessary.
• Plug the cell cord firmly into the cell housing
receptacle.
•  ResettheRCD/GFCI.
• Contact Intex Service Center.
• Contact Intex Service Center.
• Shut down and turn on the power again, re-set the
time. See “Operating Instructions”.
• Drainabout20%ofthepoolwaterandadd
fresh water to decrease the copper ion
concentration below 0.2ppm.
• Add aluminum sulfate: 1000 liters water need
around 2g (1000 gals need 0.27 ounce) or
aluminum potassium sulfate: 1000 liters water
 needaround3g(1000galsneed0.4ounce)to
pool.
• Use‘Ultra-Swim’shampoo,orshampoo
containing chelating agents.
PROBLEM CAUSE SOLUTION

Intex CS7111 Specifications

General

Brand	Intex
Model	CS7111
Category	Swimming Pool Filter
Language	English