Intex PureSpa SC-20 - Unfolding and Inflating; Inflation Outlet Tips; Power; Water Heating

244
IO
(244IO) 7.5” X 10.3” ENGLISH 08/12/2019
READ BEFORE YOU START!
NOTE: This quick start guide provides important and useful tips before you start
the setup of your spa. However, it does not address all aspects of spa installation
and use, and you are still required to read, understand, and follow the owner’s
manual for proper installation, maintenance, and safe use of your spa.
• Power:Thisproductdrawsaminimumof13AMPS.Mosthouseholdcircuitsare13to16AMPS.Ifthe
circuitbreakertrips,pleasecheckthatnootherappliancesorotherlargeloadsareonthesamecircuitas
thespa.Neveruseanextensioncord.Unfoldthelinecordpriortouse.Neverplacetheplugoncombustible
materials.
• WaterHeating:Thisheaterwhenproperlysetupandrunningwillraisethewatertemperatureby2ºCper
hourPROVIDEDthespacoverisproperlyinplace.DependingonthestartingtemperatureoftheSpawater
andexternalairtemperature,itwilltakesometimetoheatup.Ifthestartingtemperatureofyourtapwater
is22ºCandyouwantedtoraiseitby16ºCto38ºC,theheatingtimewouldbe16ºC/2ºCperhour=8hours.
Forsubsequentusetheheatingtimecanbeshortenedbymaintaininganidletemperatureinthespa(see
HEATINGANDWATERTEMPERATUREsection).BesuretokeepthecoverontheSpawhennotinuse.
• RCD:ThisproductisprovidedwithaRCDlocatedattheendofthepowercord.TheRCDmustbetested
 beforeeachuse.DoNOTusetheSpaiftheRCDdoesnotfunctionproperly.(Seeowner'smanualfor
propertestingofRCDinstructions).
• FilterCartridge:Keepthespawaterproperlysanitizedtoextendthelifeofthecartridge.Refertothe
owner’smanualfordetailedinformationonspawaterchemistryandbalance.
UNFOLDING AND INFLATING YOUR SPA:
 • Whenyouunfoldtheinatablespatubyoumaynoticethesmellofthematerialthatisnormalfor
  anewproductoutofthebox.Itisthereforerecommendedtoinatetheproductandleaveit
  outdoorsforadaytoairandallowthenewproductsmelltodissipatesomewhatbeforellingthe
  spawithwater.
 • Spreadthegroundclothwiththebubblesfacingdownovertheclearedareawhereyouintendto
  setupyourspa.
 • Forspaination,familiarizeyourselfwiththespringloadedvalveonthespatubandtheination
  outletonthecontrolboxunittoassurefastandproperination.
Ination outlet tips:
• Thelargerendoftheinationhoseattachestotheairoutletatthebackofthecontrolbaseunit(see
owner’smanualfordrawingsandfurtherdetails).
• Toattachtheinationhosetotheairoutlet,ipupthecontrolbasesidecovertorevealtheairblower
inationoutlet.Pulloutthelatchtoopenthecover,insertthehoseadaptorwithhoseandreattachthe
latchtothehoseadaptortosecureitinplace.
• Wheninationiscomplete,releasethelatch,pullouttheinationhose,andsecurethelatchbackonto
theoutlet.
NOTE:Toavoidover-ination,someairwillescapethroughthebottomair-bubbleoutletofthecontrol
baseduringination.Thisisnormal.
Spring loaded valve tips:
 • Uponremovingthevalvecap,notethespringloadedpininthecenterofthevalve.Forination,
  thespringloadedpinshouldbeintheup/raisedposition(closedpositionofthevalve)astheair
  pressureofthepumpwillpushtheairthroughthevalveduringination.Checkthevalvepinand
  assureitisintheup/raisedpositionbeforestartingination.
 • Thepincanbepresseddownandlockedintherecessedpositionbypressingandturningit90°
  clockwisewithyournger–thisistheopenpositionofthevalvethatallowstheairtoowout
  freelyandthatisusedfordeation.
SAVE THESE INSTRUCTIONS
244-*IO-R1-2008