Invacare JASMINE User Manual (English)

Other manuals for Invacare JASMINE

Questions and Answers:

A
Allison BuchananAug 15, 2025
What to do if the electric actuator fails to lift on Invacare JASMINE?
- S
  Samantha SmithAug 15, 2025
  If the electric actuator on your Invacare Lifting Systems fails to lift when the button is pressed, there are several potential causes. First, ensure that the hand-control or actuator connector is securely connected. Check the battery level and charge if necessary. Make sure the red emergency stop button is not pressed IN; rotate it clockwise until it pops out. Verify that the battery is properly connected to the control box. Inspect the connecting terminals for any damage, and replace the battery pack if needed. It's also possible that the electric actuator requires servicing or the load is too high.
M
merrittbrandonAug 18, 2025
Why lift arms will not lower in uppermost position in Invacare JASMINE?
- C
  Claire CrawfordAug 19, 2025
  If the lift arms on your Invacare Lifting Systems will not lower in the uppermost position, it's because the lift arms require a minimum weight load to lower. To resolve this, pull down slightly on the lift arms.
J
James HarveyAug 22, 2025
What to do if the Invacare Medical Equipment motor is not running?
- T
  Timothy KirbyAug 22, 2025
  If the Invacare Medical Equipment's motor isn't running, there could be several reasons. First, check that the hand control or motor plugs are fully inserted. Second, ensure the battery has power by charging or replacing it. Finally, verify that the red emergency stop button is not activated; if it is, turn it clockwise to deactivate it.
S
Sheila RamosAug 25, 2025
Why does the Invacare Medical Equipment jib motor stop during patient transfer?
- J
  Jonathan KingAug 26, 2025
  If the jib motor on your Invacare Medical Equipment stops during a patient transfer, it's likely because the maximum load has been exceeded. Reduce the load to allow the hoist to function normally.
J
John PhillipsAug 27, 2025
What to do if Invacare Medical Equipment piston rod only moves in and not out?
- M
  Michele RoseAug 27, 2025
  If the piston rod on your Invacare Medical Equipment only moves inward and not outward, it indicates that the motor is damaged and needs to be replaced.
B
Brenda BarnettAug 31, 2025
Why is there motor noise but no movement in the piston rod on my Invacare Medical Equipment?
- E
  Eileen PorterAug 31, 2025
  If you hear motor noise from your Invacare Medical Equipment, but the piston rod isn't moving, the motor is likely damaged and needs to be replaced.
E
Ebony MendozaSep 3, 2025
How to fix a loose mast on Invacare Medical Equipment?
- S
  Sarah BassSep 3, 2025
  If the mast on your Invacare Medical Equipment seems loose, it's likely that the mast screws have become loose. Tighten the screws to secure the mast.
S
Steven FernandezSep 5, 2025
What to do if Invacare Medical Equipment castors are noisy?
- M
  Mary NealSep 6, 2025
  If the castors on your Invacare Medical Equipment are noisy, it's probably due to dust or dirt. Clean the castors to eliminate the noise.
B
Brittany RodriguezSep 9, 2025
What to do if my Invacare Lifting Systems electric actuator fails to lift?
- K
  Krista BryantSep 9, 2025
  If the electric actuator on your Invacare Lifting Systems fails to lift, there are several potential causes and solutions: * **Loose Connection:** Ensure the pendant or actuator connector is properly connected, seated, and fully connected. * **Low Battery:** Charge the batteries. * **Emergency Stop:** Rotate the RED emergency stop button CLOCKWISE until it pops out. * **Battery Connection:** Reconnect the battery to the control box. * **Damaged Terminals:** Replace the battery pack.
E
Eric BrownSep 12, 2025
Why won't my Invacare JASMINE Lifting Systems boom lower in the uppermost position?
- A
  Amber FryeSep 12, 2025
  If the boom on your Invacare Lifting Systems will not lower from the uppermost position, it may require a minimum weight load to initiate lowering. Try pulling down slightly on the boom.