11
12
FP function
LOCK function
O
Keep pressing Fan button for more than 2 seconds to activate/disable Silence
function(some units).
Due to low frequency operation of compressor, it may result in insufficient cooling
and heating capacity. Press ON/OFF, Mode, Sleep, Turbo or Clean button while
operating will cancel silence function.
Silence function
Clean
5s
5s
Boost
Press this button 2 times during one second under HEAT Mode and setting temperature of
O
O
O
16 C/60 F or 20 C/68 F.
The unit will operate at high fan speed (while
compressor on) with temperature automatically
set to 8 C/46 F.
Pressing On/Off, Sleep, Mode, Fan or Temp. button while operating will cancel this function.
2
+
Press together Clean button and Boost button at the
same time more than 5 seconds to activate Lock function.
All buttons will not response except pressing these two
buttons for two seconds again to disable locking.
2s
12
LOCK function
5s
5s
Turbo
+
Press together Turbo button and Humidity button at the
same time more than 5 seconds to activate Lock function.
All buttons will not response except pressing these two
buttons for two seconds again to disable locking.
Turbo Function
Press Turbo button
Turbo
When you select Turbo feature in COOL mode,
the unit will blow cool air with strongest wind setting to
jump-start the cooling process.
When you select Turbo feature in HEAT mode,
for units with Electric heat elements, the Electric HEATER
will activate and jump-start the heating process.
Humidity
Sleep function( ) :
AP function( )(some units) :
Follow me function( ):
SET function
or
SET
SET
OK
Press the SET button to enter the function setting, then press SET button or TEMP or TEMP
button to select the desired function. The selected symbol will flash on the display area, press the
OK button to confirm.
To cancel the selected function, just perform the same procedures as above.
The FOLLOW ME function enables the remote
control to measure the temperature at its
current location and send this signal to the
air conditioner every 3 minutes interval.
When using AUTO, COOL or HEAT modes,
measuring ambient temperature from the
remote control(instead of from the indoor
unit itself) will enable the air conditioner to
optimize the temperature around you and
ensure maximum comfort.
The SLEEP function is used to decrease
energy use while you sleep (and don t need
the same temperature settings to stay
comfortable). This function can only be
activated via remote control.
Note:
The SLEEP function is not available
in FAN or DRY mode.
,
For the detail, see sleep operation in
USER S MANUAL.
,
,,
,,
,,
,,
Breeze Away function( ):
This feature avoids direct air flow blowing on the
body and makes you feel indulging in silky
coolness.
NOTE: This feature is available under cool, Fan
and Dry mode only.
FRESH function( ):
When the FRESH function is initiated, the
Ionizer/Plasma Dust Collector(depending
on models) is energized and will help to
remove pollen and impurities from the air.
,
,
,
,
,
,
,
,
If the memory feature is stopped, OF
displays for 3 seconds on the screen.
While the memory feature is activated,
press the ON/OFF button, shift the mode
or power failure will not cancel the Follow
me function.
NOTE: Press and hold Boost button for
seven seconds to start/stop memory
feature of Follow Me function.
If the memory feature is activated,
On
displays for 3 seconds on the screen.
Choose AP mode to do wireless network
configuration. For some units, it doesn’t
work by pressing the SET button. To enter
the AP mode, continuously press the LED
button seven times in 10 seconds.
*
AP mode ( ) Breeze away....
) Fresh ( ) Sleep( ) Follow Me( )
Press the SET button to scroll through operation functions as follows:
*
Breeze away ( ) Active clean/Self clean (
*
*
[ ]: Model dependent
To Next Page
Loading...
Need help?
General
