INVENTOR LDVI-12WFI/LDVO-12 User Manual

5
Buttons and Functions
Before you begin using your new air conditioner, make sure to familiarize yourself with its remote
control. The following is a brief introduction to the remote control itself. For instructions on how to
operate your air conditioner, refer to the How to Use Basic Functions
section of this manual.
ON/OFF
Turns the unit on or off.
MODE
OK
TIMER
Eco Intelligent eye
HUMIDITY
LED
Turbo
ECO/GEAR
Scrolls through operation modes
as follows:
AUTO  COOL 
DRY 
HEAT  FAN
FAN SPEED
SWING
Model:
Increases temperate in
0.5°C (1°F) increments.
Max. temperature is
30°C (86°F).
NOTE: Press together &
buttons at the same time
for 3 seconds will alternate
the temperature display
between the °C & °F.
TEMP
TEMP
04
Used to confirm the selected functions.
Used to detect the people
activities in the room to save
energy.
Decreases temperature
in 0.5 C(1 F) increments.
O
O
Min. temperature is
O
RG10L1(G2HS)/BGEF
O
16 C(60 F).
T
urns indoor unit’s LED display
and air conditioner buzzer on
and off, which create a comfortable
and quiet environment.
Adjust the room humidity during
Dry operation in a range of
35%~85%. Press this button to
increase the humidity in 5%
increments.
NOTE: After setting, the humidity
settings will display on the screen.
Set timer to turn unit on or off
Press this button to enter the
energy efficient mode in a
sequence of following:
ECO GEAR(75%)
GEAR(50%)
mode ECO
......
Selects fan speeds in the
following order:
AU


20%
60% 40% 80% 100%.



Press the TEMP or button
to increase/decrease the fan
speed in 1% increments.
Enables unit to reach preset
temperature in shortest possible time.
Previous setting
SET
Scrolls through operation
functions as follows:
Breeze away( )
clean( ) Fresh( )
Sleep( )
Follow Me( )
AP mode ( ) Breeze
Active






The selected symbol will
flash on the display area,
press the OK button to
confirm.
away( ) .......
Starts and stops the horizontal
louver movement. Hold down
for 2 seconds to initiate vertical
louver auto swing feature.
NOTE: HEAT mode is not supported
by the cooling only appliance.
Information are displayed when the remote controller is power up.
Transmission Indicator
MODE display
TIMER ON display
FAN SPEED display
TIMER OFF display
Silence feature
display
ECO display
GEAR display
LOCK display
Horizontal louver swing
display(some units)
Vertical louver auto
swing display
TURBO mode display
Not applicalbe for
this unit
Temperature/Timer/Fan speed
display
Active clean feature display
Fresh feature display
Sleep mode display
Follow me feature display
Wireless control feature display
(some units)
Low battery detection display(If flashes)
Note:
All indicators shown in the figure are for the purpose of clear presentation. But during the actaul
operation, only the relative function signs are shown on the display window.
07
Remote Screen Indicators
Displays when LOCK feature
is activated.
Silence
LOW
MED
HIGH
AUTO
Lights up when remote
sends signal to indoor
unit
Displays selected fan speed:
Displays the current
including:
mode,
2%-20%
21%-40%
41%-60%
61%-80%
81%-100%
1%
This fan speed can not be
adjusted in AUTO or DRY
mode.
Displays when ECO
feature is activated
Displays when GEAR
feature is activated
Displays the set temperature
by default, or fan speed or
timer setting when using
TIMER ON/OFF functions.
Temperature range:
o
o
o
o
16-30 C /60-86 F
Timer setting range:
0-24 hours
Fan speed setting range:
Humidity setting range:
AU -100%
35% -85%
This display is blank when
operating in FAN mode.
 

 
(20-28 C/68-82 F)
(Model dependent)
Breeze Away display
ECO intelligent eye display
(some units)
Not applicable for this unit
Not applicable for this unit
Wind flow follow people
(some units)

INVENTOR LDVI-12WFI/LDVO-12 Specifications

General

Brand	INVENTOR
Model	LDVI-12WFI/LDVO-12
Category	Air Conditioner
Language	English