Iseki SSM60 User Manual (English)

Other manuals for Iseki SSM60

Operation & Service Manual78 pages

Operators & Service Manual55 pages

Questions and Answers:

K
Kenneth JenkinsSep 2, 2025
Why do Iseki SSM60 Lawn Mower Accessories have too low engine output?
- B
  Bryan TorresSep 2, 2025
  If your Iseki Lawn Mower Accessories have too low engine output, it could be due to several reasons. Ensure you are mowing at full throttle. Reduce your traveling speed. Check for any foreign matter caught between the blade and blade support or in a pulley, and clean it. If none of these resolve the issue, the engine may be defective, in which case you should consult your dealer.
B
Barbara HallSep 1, 2025
Why are my Iseki SSM60 peeling off turf?
- J
  Joshua BeasleySep 1, 2025
  If the turf is being peeled off in some places by your Iseki Lawn Mower Accessories, it could be due to several reasons. The cutting height may be too low, so correct it with the gauge wheels. Ensure the mower is parallel to the ground by adjusting the mower mounting. Avoid turning too fast; turn slowly instead. If the ground is too bumpy, shift the mowing direction. Finally, check the tire inflation and adjust it to the specified value if it's too low.
J
jamescampbellAug 31, 2025
How to fix uneven cutting heights with Iseki Lawn Mower Accessories?
- M
  Michael RogersAug 31, 2025
  If your Iseki Lawn Mower Accessories are producing uneven cutting heights, several factors could be the cause. Ensure the mower is parallel to the ground by adjusting the mower mounting. Slow down your traveling speed. Replace worn blades with new ones. Clean any clogs inside the mower deck. Make sure the gauge wheels are properly adjusted. If the grass is too tall, mow it in two steps. Finally, check that both blades are installed on the same level and are not deformed; correct if necessary.
D
David GibbsAug 30, 2025
What to do if Iseki Lawn Mower Accessories glass is not mowed?
- R
  rrobertsAug 30, 2025
  If your Iseki Lawn Mower Accessories are not mowing the grass, several factors could be the cause. Check if the drive belt is slipping or broken; if so, adjust the belt tension spring or replace the belt. A broken tension spring should also be replaced. Other potential causes include traveling too fast (adjust mower mounting), running the engine at too low a speed (run at full throttle), worn or broken blades (replace them), or blades installed upside down (reinstall them correctly).
T
Tara BenderAug 28, 2025
Why are my Iseki Lawn Mower Accessories making excessive noise and vibration?
- C
  Crystal PerkinsAug 29, 2025
  If your Iseki Lawn Mower Accessories are making excessive noise and vibration, it could be due to several issues. Check for broken or unbalanced blades and replace them if necessary. Ensure that the blade tightening nuts are properly tightened. Also, inspect for any clogs inside the mower or foreign matter caught in a pulley and clean them. Other potential causes include a broken belt (replace it), a deformed or interfering belt cover (repair it), a damaged blade support (replace it), or damaged bevel gears (consult your dealer).
K
Kendra LarsonAug 27, 2025
What to do if blades do not rotate on Iseki Lawn Mower Accessories?
- T
  Todd ParrishAug 27, 2025
  If your Iseki Lawn Mower Accessories blades do not rotate, it could be due to several reasons. Start by checking if the blade nuts are loose and re-tighten them. Also, inspect for any foreign matter caught in the blades or blade supports and clean them. Other potential causes include a broken blade pulley or belt (replace them), slipping belts (adjust the belt tension spring), or broken bevel gears (consult your dealer).
N
Nathan AndersonAug 26, 2025
What to do if Iseki Lawn Mower Accessories peel off turf?
- N
  Natasha RoseAug 27, 2025
  If your Iseki Lawn Mower Accessories are peeling off turf in some places, consider these factors. The cutting height might be too low; correct it using the gauge wheels. Ensure the mower is parallel to the ground by adjusting the mower mounting. Avoid turning too fast; turn slowly instead. If the ground is too bumpy, try shifting the mowing direction. Finally, check the tire inflation and adjust it to the specified value.
M
mroseAug 25, 2025
How to fix uneven cutting heights on Iseki SSM60?
- M
  michelle40Aug 26, 2025
  Uneven cutting heights with your Iseki Lawn Mower Accessories can stem from a few issues. Check if the mower is parallel to the ground and adjust the mower mounting if needed. Slow down your traveling speed. Replace worn blades with new ones. Clean the inside of the mower deck if it's clogged. Ensure the gauge wheels are properly adjusted. If the grass is too tall, mow in two steps. Finally, make sure both blades are installed on the same level and are not deformed; correct them if necessary.
J
Joshua RothAug 22, 2025
Why is my Iseki SSM60 Lawn Mower Accessories not discharging properly?
- H
  Heather FrenchAug 22, 2025
  If your Iseki Lawn Mower Accessories are not discharging properly, several factors could be the cause. The drive belt might not be installed correctly, so you should check the belt and correct it if necessary. Ensure that the blades are installed correctly; if they're upside down, reinstall them properly. If the grass is too moist, wait until it dries out before mowing. For grass that's too tall or dense, try mowing in two steps or narrow the cutting width. Reduce your traveling speed and ensure the engine is running at full throttle. Finally, a clogged discharge or mower deck can also cause this issue, so be sure to clean them.
B
Brooke ColeSep 15, 2025
What to do if Iseki SSM60 blades do not rotate?