What to do if Iseki Lawn Mower calibration shows 'signal weak'?
If your Iseki Lawn Mower shows 'Cal: signal weak' during calibration, it indicates a weak or missing loop signal, or a faulty boundary cable. Place the appliance at the prescribed calibrating position, aligned at right angles. Check the power source of the base station by disconnecting and reconnecting the transformer, and inspect the boundary cable for damage.
What to do if Iseki Lawn Mower shows 'Recov escape'?
If your Iseki Lawn Mower shows 'Recov escape', automatic fault rectification was not possible. Manually acknowledge the malfunction message.
What to do if Iseki Lawn Mower shows 'Blocked WR'?
If your Iseki Lawn Mower displays 'Blocked WR', it means the right wheel motor is blocked. Remove the blockage.
What to do if Iseki Lawn Mower shows 'Blocked WL'?
If your Iseki Lawn Mower displays 'Blocked WL', it indicates that the left wheel motor is blocked. Remove the blockage.
What to do if Iseki Lawn Mower shows 'Cal: Collision' during calibration?
If your Iseki Lawn Mower shows 'Cal: Collision' during calibration, it means the appliance has bumped into an obstacle. Remove the obstacle.
What to do if Iseki Lawn Mower blade motor is overheating?
If your Iseki Lawn Mower displays 'Blade motor over heating', it means the mowing motor has overheated (more than 80 °C). Switch off the appliance and let it cool down.
What to do if Iseki Lawn Mower shows 'Lift sensor' error?
If your Iseki Lawn Mower shows a 'Lift sensor' error, it means the appliance cover has been deflected upwards by lifting or by an obstacle. Remove the obstacle to resolve this issue.
What to do if Iseki Lawn Mower displays 'Tilt sensor' error?
If your Iseki Lawn Mower displays a 'Tilt sensor' error, it means the inclination sensor has been triggered because the maximum tilt was exceeded, the appliance has been carried, or the slope is too steep. Place the appliance on a flat surface and acknowledge the fault.
What to do if Iseki Lawn Mower battery is overheating?
If your Iseki Lawn Mower displays 'Battery over heating', it means the rechargeable battery has overheated (more than 60 °C). Switch off the appliance and let the rechargeable battery cool down. Do not place the appliance on the base station while it cools.
What to do if Iseki Lawn Mower shows 'No loop signal'?
If your Iseki Lawn Mower shows a 'No loop signal' error, it could be due to several reasons. First, there might be no loop signal at all. Second, the boundary cable might be faulty, or the loop signal could be too weak. To resolve this, check the LEDs on the base station and ensure the power source of the base station is working by disconnecting and reconnecting the transformer. Also, inspect the boundary cable for any damage and repair it if necessary.
Explains danger, warning, caution, and important notices used in the manual.
Lists all items included in the product package for verification.
Details the automatic, battery-operated lawn mower and its adjustable cutting height.
Explains the meaning of various safety and operational symbols found on the appliance.
Describes the functions of buttons and indicators on the appliance's control panel.
Explains the display screen layout, menu items, and navigation functions.
Provides a hierarchical overview of the appliance's menu options and their corresponding functions.
Details the components, functions, and charging capabilities of the base station.
Information about the permanent battery, charging, and maintenance.
Explains how the automatic lawn mower moves and operates on the grass surface.
Specifies the intended non-commercial use and application limits of the appliance.
Lists unsuitable environments or applications for the lawn mower.
Outlines essential safety features and protective mechanisms of the appliance.
Provides critical instructions for safe operation, covering operator, persons, animals, and appliance.
Step-by-step guide for carefully unpacking and checking the appliance for damage.
Guidance on selecting the optimal location and layout for the mowing area.
Steps to prepare the lawn, including removing obstacles and mowing to a low height.
Instructions for correctly installing and positioning the base station and extension plate.
Procedures for connecting and routing the boundary wire around the mowing area.
Methods for routing the boundary cable to avoid obstacles and ensure proper operation.
Techniques for navigating the boundary cable around internal and external corners.
Guidelines for creating narrow passages between mowing areas using boundary cable.
How to use the boundary cable to exclude areas with steep downward slopes.
Instructions for incorporating spare cable loops for future repositioning or area extension.
Identifies common issues and errors encountered during boundary cable installation.
Steps for safely connecting the base station to the electrical power supply.
How to verify correct installation and operation using the base station's LEDs.
Guide to fully charging the battery before first use and during normal operation.
Initial configuration steps including language, PIN, date, and time setup.
Instructions on how to adjust the lawn mower's cutting height.
Procedure to calibrate the appliance for optimal boundary cable detection and navigation.
Steps to manually start and stop the lawn mower operation.
How to stop the mowing process prematurely and its consequences.
Instructions for manually moving and operating the mower in secondary mowing zones.
How to access and navigate the appliance's main settings menu.
How to activate, deactivate, and set delays for the rain sensor.
Guide to enable or disable the energy-saving Eco mode for reduced consumption.
Overview of how to set up general mowing schedules and parameters.
Procedure for teaching the appliance specific starting points for mowing.
How to program daily mowing schedules, including specific times and mowing types.
Setting up edge mowing for manual starts, especially in secondary areas.
Configuration for mowing secondary zones, including time limits.
Adjusting screen contrast for better readability in various lighting conditions.
How to activate or deactivate the setting lock feature for security.
Procedure to recalibrate the appliance when boundary cable positions change.
How to reset the appliance to its original factory default settings.
Information on blade service intervals and resetting the service counter.
Appliance information like serial number, operating hours, and cycles.
Shows the current firmware version of the appliance.
Displays current settings such as the total weekly mowing time.
Lists recent fault messages with date, time, and fault code.
Instructions for cleaning the automatic lawn mower and its base station.
Weekly checks for damage on the machine, base station, and cables.
Step-by-step guide for safely replacing worn or damaged cutting blades.
Procedure for replacing a blown fuse in the appliance's transformer.
Guidelines for storing the appliance, especially for winter or long periods.
Recommendations for storing the base station to prevent premature aging.
How to protect the boundary cable ends during winter storage.
A table listing common malfunctions, their causes, and suggested remedies.
Details specific fault codes, their causes, and troubleshooting steps.
Continues listing fault codes, their causes, and troubleshooting steps.
Continues listing fault codes, their causes, and troubleshooting steps.
Continues listing fault codes, their causes, and troubleshooting steps.
Explains danger, warning, caution, and important notices used in the manual.
Lists all items included in the product package for verification.
Details the automatic, battery-operated lawn mower and its adjustable cutting height.
Explains the meaning of various safety and operational symbols found on the appliance.
Describes the functions of buttons and indicators on the appliance's control panel.
Explains the display screen layout, menu items, and navigation functions.
Provides a hierarchical overview of the appliance's menu options and their corresponding functions.
Details the components, functions, and charging capabilities of the base station.
Information about the permanent battery, charging, and maintenance.
Explains how the automatic lawn mower moves and operates on the grass surface.
Specifies the intended non-commercial use and application limits of the appliance.
Lists unsuitable environments or applications for the lawn mower.
Outlines essential safety features and protective mechanisms of the appliance.
Provides critical instructions for safe operation, covering operator, persons, animals, and appliance.
Step-by-step guide for carefully unpacking and checking the appliance for damage.
Guidance on selecting the optimal location and layout for the mowing area.
Steps to prepare the lawn, including removing obstacles and mowing to a low height.
Instructions for correctly installing and positioning the base station and extension plate.
Procedures for connecting and routing the boundary wire around the mowing area.
Methods for routing the boundary cable to avoid obstacles and ensure proper operation.
Techniques for navigating the boundary cable around internal and external corners.
Guidelines for creating narrow passages between mowing areas using boundary cable.
How to use the boundary cable to exclude areas with steep downward slopes.
Instructions for incorporating spare cable loops for future repositioning or area extension.
Identifies common issues and errors encountered during boundary cable installation.
Steps for safely connecting the base station to the electrical power supply.
How to verify correct installation and operation using the base station's LEDs.
Guide to fully charging the battery before first use and during normal operation.
Initial configuration steps including language, PIN, date, and time setup.
Instructions on how to adjust the lawn mower's cutting height.
Procedure to calibrate the appliance for optimal boundary cable detection and navigation.
Steps to manually start and stop the lawn mower operation.
How to stop the mowing process prematurely and its consequences.
Instructions for manually moving and operating the mower in secondary mowing zones.
How to access and navigate the appliance's main settings menu.
How to activate, deactivate, and set delays for the rain sensor.
Guide to enable or disable the energy-saving Eco mode for reduced consumption.
Overview of how to set up general mowing schedules and parameters.
Procedure for teaching the appliance specific starting points for mowing.
How to program daily mowing schedules, including specific times and mowing types.
Setting up edge mowing for manual starts, especially in secondary areas.
Configuration for mowing secondary zones, including time limits.
Adjusting screen contrast for better readability in various lighting conditions.
How to activate or deactivate the setting lock feature for security.
Procedure to recalibrate the appliance when boundary cable positions change.
How to reset the appliance to its original factory default settings.
Information on blade service intervals and resetting the service counter.
Appliance information like serial number, operating hours, and cycles.
Shows the current firmware version of the appliance.
Displays current settings such as the total weekly mowing time.
Lists recent fault messages with date, time, and fault code.
Instructions for cleaning the automatic lawn mower and its base station.
Weekly checks for damage on the machine, base station, and cables.
Step-by-step guide for safely replacing worn or damaged cutting blades.
Procedure for replacing a blown fuse in the appliance's transformer.
Guidelines for storing the appliance, especially for winter or long periods.
Recommendations for storing the base station to prevent premature aging.
How to protect the boundary cable ends during winter storage.
A table listing common malfunctions, their causes, and suggested remedies.
Details specific fault codes, their causes, and troubleshooting steps.
Continues listing fault codes, their causes, and troubleshooting steps.
Continues listing fault codes, their causes, and troubleshooting steps.
Continues listing fault codes, their causes, and troubleshooting steps.
General| Brand | Iseki |
|---|---|
| Model | SRE2600X |
| Category | Lawn Mower |
| Language | English |
To Next Page
