ITC VersiControl 22500-RGBW Series - User Manual

3030 Corporate Grove Dr. • Hudsonville • MI • 49426
Phone: 616-396-1355 • www.itc-us.com • sales@itc-us.com • DOC#: 710-00025 Rev F • 09/20/17
VersiControl RGBW Smart System Install Instructions
(Part #’s: 22500-RGB-XX & 22500-RGBW-XX)
Safety Instructions
• Disconnect power before installing, adding or changing any component.
• To avoid a hazard to children, account for all parts and destroy all packing materials.
• Do not install any luminaire assembly closer than 6” from any combustible materials.
• Positive (+) outputs require a fuse if the attached wire leads are not rated to handle the max current.
• This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference
- This device must accept any interferences received, including interference that may cause undesired operation
For warranty information please visit www.itc-us.com
1. INSTALL: Determine the installation location for your control module. Make sure to consider the size of the module (7.5”L x 5”W x 1.5”H)
when determining your location. Note, it will require room for access and for wiring. Screw the controller in place using four M5 stainless
steel screws (not provided) sized appropriately for the substrate material used. Make sure when mounted, that the Bluetooth antenna is
not obstructed by metal objects.
1.5”
7.5”
5”
PARTS / TOOLS NEEDED:
VersiControl RGB
Smart System
Smart Pad
(Optional)
RGB Lighting
(Varies)
Mounting Screws x 4
(not provided)
Butt Splices
(not provided)
Power Drill
2. CONNECT CONTROL PAD: If using the control pad (optional), insert
the connector on the control pad into the connector on the
module. Refer to control pad installation instructions for more
detailed information.
3. ZONE WIRE CONNECTIONS: Refer to the diagram below for refer-
ence when wiring the system in step 4. Note, there can be 16 or
20 zone wires coming out of the controller. Each wire has been
individually placed on the grommet of the assembly.
G WBR+
G WBR+
G +RBW
G +RBW
ZONE 1
ZONE 2
ZONE 3
ZONE 4
Bluetooth Antenna

ITC VersiControl 22500-RGBW Series Specifications

General

Category	Controller
Series	VersiControl 22500-RGBW
Manufacturer	ITC
Output Channels	4
Voltage Input	12-24V DC
Max Output Current per Channel	5A
DMX Channels	4
Control Method	DMX
Control Protocol	DMX512
Operating Temperature	-20°C to 50°C

Summary

Parts and Tools Needed

Safety Instructions

General Safety Precautions

Essential safety guidelines including power disconnection, child safety, clearance, and FCC compliance.

Installation Guide

Module Installation

Determine module location, considering size and access. Mount using M5 screws, ensuring Bluetooth antenna is unobstructed.

Control Pad Connection

Connect the control pad to the module. Refer to control pad instructions for detailed information.

Zone Wire Connections Diagram

Diagram for zone wire connections, noting 16 or 20 zone wires individually placed on the grommet.

Wiring Diagrams

RGBW Wiring Diagram

Wiring diagram for the 22500-RGBW-XX controller, showing inputs, outputs, and connectors.

RGB Wiring Diagram

Wiring diagram for the 22500-RGB-XX controller, showing inputs, outputs, and connectors.

System Customization

CAN Bus Address Configuration

Configure the CAN address using dip switches 1 and 2 for multiple controllers on a CAN network.

Bluetooth Pass Code Reset

Reset the Bluetooth pass code by switching dip switch 3 on and then off.

Power-Up State Selection

Select controller power-up state (ON or OFF) using dip switch 4.

Optional Input Line Disable

Input Line Zone Control

Disable zones 1 & 2 via input line (Pin 4); adjustable via CAN interface. Default is zones 1 and 2.