Jacuzzi J-300 - Spa Programming and Configuration; Filtration and Timer Settings

37
Note: Turning o the corresponding jets pump that is running can
deactivate the feature.
Clean-up Cycle
The cleanup cycle occurs once per day at 12:00 PM (noon) for 2
minutes. This is not user programmable. The Jets Pump 1 and the
Circulation Pump will turn on for one minute and then shut o.
Then Jets Pump 2 will turn on and run for 1 minute then shut o.
Note: Turning o the corresponding jets pump that is running can
deactivate the feature.
Menu Features and Programming Instructions
Your spa is equipped with menus that allow you to program addi-
tional features. By continually pressing the Menu ( ),button you
will cycle through the menus as follows:
Current temperature (Main Menu)
Primary Filtration
Secondary Filtration
Heat
Filter Change
UV
H2O
Time
Date
Temp
Language
Lock
WiFi
S\N
 Primary Filtration Menu
During the primary ltration cycle, the circulation pump and
CLEARRAY are activated. The spa is programmed with a default
setting starting at 12:00 AM and lasting for 8 hours, but this can
be changed. This cycle allows the circulation pump to run for a
preset amount of time per day, in addition to the normal oper-
ation.
Note: Any time the circulation pump runs outside of a program
cycle, e.g. for heating, that run time will be deducted from the
next primary lter cycle. For example, the primary lter cycle is
set to 8 hours every 24 hours but the circulation pump comes on
for 2 hours to heat the water after the cycle has nished. The next
primary lter cycle will only be for 6 hours not 8 hours.
 Programming the Primary Filtration Cycle
To change the programmed Primary Filtration Cycle:
1. Press (
) until you see the menu “PF”. The text “PRIMARY
FILTER” (primary ltration cycle) scrolls across the screen. The
system returns to the main menu if no action is taken.
2. Press or to display the current start time and prepare
the system for changes.
3. Press or to adjust the start time, in 1-hour increments.
To switch from “AM” to “PM” you must round a 12-hour period.
4. Press (
1
) to conrm and save the start time.
5. Press or to adjust the duration of cycle, in 1-hour incre-
ments.
6. Press (
1
) to conrm and save the duration time. The system
will return to the “PRIMARY FILTER” Menu.
Note: If no button is pressed within 5 seconds of each selection
the screen will revert back to the Main Menu and the current set-
tings will remain active.

In extreme bitter cold weather, where freezing can
occur, we recommend you program the primary l-
tration cycle to run 24 hours. Refer to the “Winteriz-
ing” section.
 Secondary Filtration Menu
The spa is programmed with a default setting of Holiday Mode,
but can be programmed to other modes. There are 3 dierent
modes, Holiday, Light and Heavy Mode.
Note: During the secondary ltration the jets pump 1, circulation
pump and CLEARRAY are activated.
• Holiday Mode disables the Secondary Filtration.
• Light Mode will activate two 10-minute cycles every other
day; one at 8:00 AM and the other at 8:00 PM.
• Heavy Mode will activate two 10-minute cycles every day;
one at 8:00 AM and the other at 8:00 PM.
Programming the Secondary Filtration Cycle
To change the programmed Secondary Filtration Cycle:
Note: If no button is pressed within 5 seconds of each selection
the screen will revert back to the Main Menu and the current set-
tings will remain active.
1. Press ( ) until you get to the “SF” Menu. The display will scroll
“SECONDARY FILTER.” The system returns to the main menu if
no action is taken.
2. Press or to enter the Secondary Filtration programming.
Continually press to scroll through the following modes:
• Holiday Mode: The screen will display “HOL” and scroll “HOL-
IDAY MODE.”
• Light Mode: The screen will display “LT” and scroll “LIGHT
MODE.”
• Heavy Mode: The screen will display “HVY” and scroll “HEAVY
MODE.”
3. Once a selection is made, press () to conrm and activate the
setting. The system will return to the “SECONDARY FILTER” Menu.
 Programming the Heating Mode
Your Jacuzzi spa is equipped with 3 modes of heating. An auto-
matic mode called “AUTO,” where the spa’s temperature is main-
tained at all times. An energy saving heating cycle called “ECO.” A