41
There are certain precautions to keep in mind when draining your
spa. If it is extremely cold, and the spa is outdoors, freezing could
occur in the lines or the equipment, see “WINTERIZING”.
To drain your spa, perform the following steps:
1. Turn o power to spa at breaker.
2.
3.
4.
5.
2.
3.
4.
5.
2. Identify the drain valve, from the front, on the lower part of the
support base. Hold the rear ring nut still to stop it from turning,
then loosen and remove the front cap to expose the underlying
male pipe thread.
3. Attach a garden hose to the exposed threads.
4. Gently rotate the larger (rear) valve body 1/3 turn counter-
clockwise to unlock the drain valve.
5. Pull the larger (rear) body outward to open drain.
6. After the spa drains, perform steps 2-5 in reverse order to close
the drain prior to relling the spa.
7. Once the hot tub has been lled, turn it on and follow the in-
structions for lling (see the relevant section).
N.B.: Always ll your spa through both lter wall ttings.
Cleaning The Spa Interior
To preserve the sheen of your spa’s surface, it is crucial that you avoid
using abrasive cleaners or cleaners which have adverse chemical ef-
fect on the surface. If you are not certain as to the suitability of a par-
ticular cleanser, consult your authorized Jacuzzi dealer. Regardless
of the cleanser used, use extreme care to assure that no soap residue
is left on the surface. This could cause severe sudsing when the spa
is relled.
Information regarding cleaning the hot tub, maintenance
and the products to be used can be found in the guide/cata-
logue supplied with the product.
Pillow Care
B
A
C
Remove and clean the headrest pillows as needed with soapy
water using a cloth or soft-bristle brush.
N.B.: Always remove the headrests when adding a chemical shock
treatment to the water. The headrests can be put back in the hot tub
when the disinfectant product value reaches a normal level again
(see the water treatment guide).
To remove pillows:
1. Grasp pillow insert (A) with nger tips and gently pry outward
from pillow base (B).
2. Grasp pillow base (B) with nger tips and gently pry outward
from spa shell (C).
3. Assemble in reverse order after cleaning.
Vinyl Cover Care and Maintenance
Your Jacuzzi cover has a vinyl encasement. This vinyl encasement
is attractive and durable. Monthly cleaning and conditioning is
strongly recommended to maintain and increase the longevity of
your cover.
To Clean and Condition the Vinyl Cover
1. Use a garden hose to loosen debris and dirt.
2. Using a large sponge or a soft bristle brush, use diluted or mild
soap and scrub the vinyl top. Rinse clean and do not allow soap
to dry on cover. Do not use soap on the underside of the cover.
3. Please check with your Jacuzzi Dealer for recommended cov-
er care and conditioning products. Condition using non-petro-
leum based conditioners to keep the vinyl supple and threads/
stitching from drying out. Do not use solvents, abrasive cleaners
or strong detergents. Do not use products that contain silicone
or alcohol.
To Clean and Condition the ProEndure™ cover:
1. Brush o dirt, leaves and any loose debris.
2. Thoroughly hose down the cover.
3. Using a large sponge or a soft bristle brush, use diluted or mild
soap (such as woolite or dreft, no detergents) and scrub the cov-
er. Allow the solution to soak in.
4. Rinse clean and do not allow soap to dry on cover. Continue to
rinse until all the soap solution is removed. Do not use soap on
the underside of the cover. The fabric dries quickly allow it to air.
Do not apply heat or machine dry.
5. Retreating the fabric, using 303 High Tech Fabric Guard™, after
cleaning is highly recommended. Follow the instructions from
the manufacturer.
6. Additional cleaning and care information may be found at
www.sunbrella.com
NOTE: Do not use solvents, abrasive cleaners or strong deter-
gents. Do not use products that contain silicone or alcohol.
To Next Page
Loading...
Need help?
General
