Need help?Do you have a question about the Jacuzzi lodge S and is the answer not in the manual?
General| Voltage | 240V |
|---|---|
| Shell Material | Acrylic |
| Frame Material | Wood |
| Insulation | Full Foam |
| Pump | 2 HP |
| Warranty | 5 years |
Ensure user awareness of safe operation, water quality checks, and proper chemical usage.
Verify required components like filling system, drain, water softener, and electrical connections.
Handle hot tub carefully during transport and inspect packaging and components upon arrival.
Choose a suitable base and protect the hot tub from prolonged sun exposure to prevent material damage.
Connect plumbing to mains and drain, and ensure electrical connections meet standards and are safely installed.
Installer is responsible for safe electrical installation; Jacuzzi denies liability for non-compliance or unauthorized work.
Configure system software via control panel to limit electrical consumption using specific key presses and passwords.
Ensure filter cartridge is present, drain valve is closed, and all hydromassage intakes are open before filling.
Fill the hot tub to cover the highest nozzles and turn on the all-pole circuit breaker to start the system.
Refer to corresponding drawings for the correct installation of front and side panels.
All hot tub functions and settings are managed via the control panel, including navigation with Up/Down keys.
Convert temperature display between Celsius (°C) and Fahrenheit (°F) using control panel key sequences.
Check and adjust the water temperature set point using Up/Down keys, with a specified range and heater shut-off behaviour.
Notes on heater LED status indicating heating suspension due to consumption limits and information on heating rate.
System automatically activates heater and pump to maintain minimum temperature and protect pipes from freezing.
Water needs filtering for cleanliness; cycles run daily, with some models having a fast "Boost" option.
Set filtering cycle duration and start delay using the 'Light' and 'Up/Down' keys, with factory default settings provided.
Filtering cycles can be suspended by hydromassage, standby mode, or anti-freeze protection, resuming later.
Filtering cycles suspend if water temperature exceeds set point by 1°C for 3 hours, resuming when temperature drops.
Clearray™ oxidizes organic substances, reducing the need for chemical treatments.
Activate rapid filtering for intensive use or chemical treatment, lasting 45 minutes, pump runs with Clearray.
Activate hydromassage pump at low or high speed depending on the model and function, with automatic shut-off.
Activate the air compressor (blower) for 20 minutes; can be used for aroma therapy with cartridges.
Control the underwater spotlight using the 'Light' key, which stays on for two hours or can be manually turned off.
Suspend all system devices for 60 minutes for routine maintenance without disconnecting power.
CAUTION: Disconnect electric power by turning off the all-pole circuit breaker before accessing electronic or rotating parts.
Alarms are indicated on the display with corresponding error codes, persisting if the condition remains.
Details specific alarm codes like FLO (flow switch), HOH (high temp), Ho (excessive temp), H2O (low water level), and their solutions.
Addresses errors related to defective temperature probes (rPF) and safety thermostat activation (HPF) due to overheating.
Troubleshoot dirty water by checking filter, water treatment, and maintenance, with solutions like cleaning filters or consulting treatment guides.
Address excessive water consumption by repairing leaks, using the hot tub cover, or lowering the water temperature set point.
Troubleshoot low hydromassage flow due to low water level, clogged filter, partially closed jets, or pipe blockages.
Resolve no water flow issues by checking power, pump status, motor connection, main switch, and resetting RCCB.
Address noisy pump and motor by cleaning filters, finding and repairing leaks, or checking motor bearings and impeller.
Troubleshoot motor start-up failures related to power, switch status, voltage, breaker trips, connections, or motor windings.
Resolve motor stopping issues due to function end, overload, or unsuitable power supply cables.
Troubleshoot blower non-operation by checking power, button presses, switch status, breaker trips, or faulty motor.
To Next Page
