Need help?Do you have a question about the Jacuzzi LED Series and is the answer not in the manual?
Details how to utilize the S.T.A. manual for effective communication and time saving.
Advises using the S.T.A. for systematic problem-solving, prioritizing least expensive parts.
Provides three key steps to protect circuit boards from static discharge during handling and installation.
Details the buttons and functions of the J-LX control panel, including display and operation.
Explains the buttons and functions of the J300 control panel for both 1-pump and 2-pump models.
Describes the buttons and functions of the J200 control panel for different model configurations.
Provides two methods to set the filter cycle start time for specific hot tub collections.
Explains standard and economy filtration modes and their effects on spa operation and energy consumption.
Details how to select filter cycles and lock modes for J-LX and J300 collections.
Explains how to program filter cycles and lock modes for specific J200 models.
Details how to program filter cycles and lock modes for J200 models without a circulation pump.
Guides on setting the circulation pump's filtration cycle duration.
Instructions for programming the CLEARRAY system or Corona Discharge Ozone.
Instructions for programming CLEARRAY on models without a circulation pump.
Provides specifications and operational details for 2011 aftermarket ozonator systems.
Explains the CLEARRAY system, its operation, and specifications for 2012+ models.
Details how to set the water temperature and access the overtemp feature.
Explains how to adjust the speed for different jet pumps and their automatic shut-off.
Details how to operate the multicolored light system, including modes and sequences.
Explains how to operate the standard spa light, including color selection and modes.
Describes how to operate the multi-colored LED lighting system in the J200 collection.
Table detailing jumper configurations for North American 1-pump models.
Table detailing jumper configurations for North American 2-pump models.
Details jumper settings for specific circuit board models in domestic 60 Hz systems.
Explains jumper configurations for export 50 Hz 1-pump models.
Details jumper settings for export 50 Hz 2-pump models.
Explains how control panel displays indicate operation status and potential issues.
Lists common error messages (SN1, SN2) and their probable causes and troubleshooting steps.
Discusses troubleshooting steps for flow/pressure switch errors (FL1, FL2).
Details the "OH" overheat condition and troubleshooting steps.
Explains the "Watchdog" error message indicating a potential destructive condition.
Provides detailed procedures for testing flow and pressure switches.
A flowchart for diagnosing and resolving no/low heat issues.
Troubleshooting steps when the hot tub has no operation at all (panel lit or dead).
Steps to troubleshoot when the hot tub fails to start its filter cycle.
Explains how to diagnose tripping house breakers or GFCI issues.
Diagnosing and resolving issues when the jets do not operate.
Essential steps to measure voltage at the terminal block for safe and proper operation.
Lists current draw for major hot tub components for troubleshooting.
Provides a voltage chart for hot tub components to help diagnose circuit board or device issues.
Procedures for testing flow and pressure switches when FL1/FL2 messages appear.
Explains fuse function and lists part numbers for different models.
Explains the "Watchdog" error message and its causes like sensor or board issues.
Explains the function of CLEARRAY and Ozone sanitizing systems.
Discusses the importance of maintaining proper pH for water quality and sanitation.
Wiring diagram for convertible 1-pump models, showing connections and jumper settings.
Wiring diagram for North American 240V 1- or 2-pump models.
Wiring diagram for export 50 Hz 1-pump models.
Wiring diagram for export 50 Hz 1- or 2-pump models.
Diagrams showing load box connections for North American 60 Hz models.
Guide to troubleshooting the optional stereo system, including wiring diagrams.
Definitions of technical terms used in the manual.
A form for collecting troubleshooting data before contacting technical support.
To Next Page
General